Formato De Datos Midi; Control Change - Yamaha Clavinova CLP-130 Manual De Instrucciones

MIDI Data Format / MIDI-Datenformat /
Format des données MIDI / Formato de datos MIDI
If you're already very familiar with MIDI, or are using a
computer to control your music hardware with computer-
gener-ated MIDI messages, the data provided in this section
can help you to control the CLP-130/120.
Falls Sie bereits mit MIDI vertraut sind oder einen
Computer zur Erzeugung von MIDI-Steuermeldungen für die
Instrumente verwenden, können Sie sich zur Steuerung des
CLP-130/120 nach den im folgenden Abschnitt aufgeführten
Spezifikationen richten.
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number)
kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /
Receive: 00H ~ 7FH = C-2 ~ G8)*
vv = Velocity (Key ON = 01H ~ 7FH, Key OFF = 00H)
Data format: [8nH] -> [kk] -> [vv] (reception only)
8nH = Note OFF event (n = channel number)
kk = Note number: 00H ~ 7FH = C-2 ~ G8
vv = Velocity
* If received value exceeds the supported range for the
selected voice, the note is adjusted by the necessary num-
ber of octaves.

2. CONTROL CHANGE

Data format: [BnH] -> [cc] -> [vv]
BnH = Control change (n = channel number)
cc = Control number
vv = Data Range
(1) Bank Select
ccH Parameter
00H Bank Select MSB
20H Bank Select LSB
Bank selection processing does not occur until receipt of
next Program Change message.
(2) Main Volume (reception only)
ccH Parameter
07H Volume MSB
(3) Expression
ccH Parameter
0BH Expression MSB
(4) Damper
ccH Parameter
40H Damper MSB
(5) Sostenuto
ccH Parameter
42H Sostenuto
(6) Soft Pedal
ccH Parameter
43H Soft Pedal
(7) Effect1 Depth (Reverb Send Level)
ccH Parameter
5BH Effect1 Depth
Adjusts the reverb send level.
(8) Effect4 Depth (Variation Effect Send Level)
ccH Parameter
5EH Effect4 Depth
Data Range (vvH)
00H:Normal
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H-3FH:off, 40H-7FH:on
Data Range (vvH)
00H-3FH:off, 40H-7FH:on
Data Range (vvH)
00H...7FH
Data Range (vvH)
00H...7FH
Si vous êtes très familier avec l'interface MIDI ou si vous
utilisez un ordinateur pour commander votre matériel de
musique au moyen de messages MIDI générés par
ordinateur, les données suivantes vous seront utiles et vous
aideront à commander le CLP-130/120.
SI usted está ya familiarizado con MIDI, o si emplea una
computadora para controlar sus aparatos musicales con
mensajes MIDI generados por computadora, los datos
proporcionados en esta sección le ayudarán a controlar la
CLP-130/120.
3. MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number)
cc = Control number
vv = Data Range
(1) All Sound Off
ccH Parameter
78H All Sound Off
Switches off all sound from the channel. Does not reset Note
On and Hold On conditions established by Channel Messages.
(2) Reset All Controllers
ccH Parameter
79H Reset All Controllers
Resets controllers as follows.
Controller
Expression
Damper Pedal
Sostenuto
Soft Pedal
(3) Local Control (reception only)
ccH Parameter
7AH Local Control
(4) All Notes Off
ccH Parameter
7BH All Notes Off
Switches OFF all the notes that are currently ON on the spec-
ified channel. Any notes being held by the damper or soste-
nuto pedal will continue to sound until the pedal is released.
(5) Omni Off (reception only)
ccH Parameter
7CH Omni Off
Same processing as for All Notes Off.
(6) Omni On (reception only)
ccH Parameter
7DH Omni On
Same processing as for All Notes Off.
(7) Mono (reception only)
ccH Parameter
7EH Mono
Same processing as for All Sound Off.
(8) Poly (reception only)
ccH Parameter
7FH Poly
Same processing as for All Sound Off.
• When control change reception is turned OFF in the Function
mode, control change data will not be transmitted or received
except for Bank Select and Mode messages.
• Local on/off, OMNI on/off are not transmitted. (The appropriate
note off number is supplied with "All Note Off" transmission).
• When a voice bank MSB/LSB is received, the number is
stored in the internal buffer regardless of the received order,
then the stored value is used to select the appropriate voice
when a program change message is received.
• The Multi-timbre and Poly modes are always active. No
change occurs when OMNI ON, OMNI OFF, MONO, or POLY
mode messages are received.
Data Range (vvH)
00H
Data Range (vvH)
00H
Value
127 (max)
0 (off)
0 (off)
0 (off)
Data Range (vvH)
00H (off), 7FH (on)
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Data Range (vvH)
00H
Appendix
CLP-130/120
71