Technical Data; Double Insulation; Additional Handle - Narex EV 13 F‑H3 Instrucciones De Uso

Technical data

Drilling machine and impact drill
Type
Supply voltage (V)
Power frequency (Hz)
Power input (W)
Speed under load (rpm)
1st speed gear
2nd speed gear
Idle speed (rpm)
1st speed gear
2nd speed gear
Number of impacts (ipm)
1st speed gear
2nd speed gear
Speed pre-selection
Right-left turning
Extent of chuck dia. (mm)
Thread on spindle
Inner hexagon in spindle
Drilling dia. max (mm)
into steel
into aluminium
into wood
into concrete
Clamping neck dia. (mm)
Weight (kg)
Protection class
Controls
1 ...........Chuck with ring gear
2 ...........Spots on spindle
3 ...........Clamping neck
4 ...........Lever for impact shifting
5 ...........Air vents
6 ...........Stop bar

7 ...........Additional handle

8 ...........Gear-shifting lever (EV 13 E-2H3, EVP 13 E-2H3)
9 ...........Alteration switch lever (EVP 13 E-2H3)
10 .........Speed pre-selection wheel
11 .........Switch / controller
12 .........Latching pin
13 .........Screw shaft
14 .........Spindle cover
15 .........Drilling spindle
16 .........Chuck hook
17 .........Spanner
18 .........Socket screw wrench
19 .........Quick-tightening chuck
The displayed or described accessories need not be included in the
delivery package.

Double insulation

To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards). Tools
with double insulation are marked by the international symbol of
a double square. These tools must not be grounded and a two-wire
cable is sufficient to supply them with power. Tools are shielded in
accordance with EN 50114.
EV 13 F-H3 EV 13 E-2H3
230 V 230
50–60 50–60
650 W 650
0–2 275 0–630
0–1 730
û
0–4 000 0–1 100
0–3 000
û
û û
û û
ü ü
ü ü
1,5–13 1,5–13
1/2"–20 UNF 1/2"–20 UNF
1/4"
û
13 13
16 16
25 35
û û
43 43
1.5 1.7
II / II /
Use
The machine is intended drilling in wood, metal, ceramic and plas-
tic. Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting ( Only for soft screwdriv-
ing applications).
EVP 13 E-2H3:
The machine is intended for impact drilling in brick, concrete and
stone as well as for drilling in wood, metal, ceramics and plastics.
Machines with electronic control and right/left rotation are also
suitable for screwing and thread-cutting.
The user alone is responsible for any liabilities caused by usage
other than intended.
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore
follow these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or
stoppage.
- Always change the speed gear when the machine is idle or at
the machine slow-down at low speed, in no case during the
drilling or when the machine is otherwise loaded.
Check whether the data on the name plate correspond with the
actual power supply voltage. Tools designed for 230 V may be con-
nected also to 220 / 240 V.
Additional handle
For safety reasons always use the additional handle (7), firmly
mounted on the clamping neck (3). The stop bar (6) can be used to
adjust the drilling depth.
EVP 13 E-2H3
230
50–60
650
0–630
0–1 730
0–1 100
0–3 000
0–12 600
0–34 600
ü
ü
1,5–13
1/2"–20 UNF
1/4"
13
16
35
16
43
1.8
II /
Attention! Prior to handling the accessories, the pow-
er supply cable has always to be disconnected from
the power source socket!
English
15