Special Safety Instructions - Narex EBU 115-10 Instrucciones De Uso Originales

safety shoes, hard hat, or hearing protection used for appro-
priate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off‑position before connecting to power source and/or bat‑
tery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unex-
pected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extrac‑
tion and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dust-re-
lated hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any ad‑
justments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condi‑
tion that may affect the power tool's operation. If dam‑
aged, have the power tool repaired before use. Many acci-
dents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control..
g) Use the power tool, accessories and tool bits etc. in ac‑
cordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
the power tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.

Special Safety Instructions

Collective Safety Warnings for Grinding,
Sanding, Wire Brushing and Abrasive Cutting‑
Off Operations:
a) This power tool is intended to function as a grinder, sand‑
er, wire brush and cut‑off tool. Read all safety warnings,
instructions, illustrations and specifications provided with
this power tool. Failure to follow all the instructions may re-
sult in electric shock, fire and/or serious injury.
b) This power tool is not suitable for polishing work. Opera-
tions for which the power tool was not designed may create
a hazard and cause personal injury.
c) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because
the accessory can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool. In-
correctly sized accessories cannot be adequately guarded or
controlled.
f) The arbour size of wheels, flanges, backing pads or any
other accessory must properly fit the spindle of the pow‑
er tool. Accessories with arbour holes that do not match the
mounting hard-ware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect
the accessories such as abrasive wheels for chips and
cracks, backing pads for cracks, tear or excess wear, wire
brushes for loose or cracked wires. If power tool or accesso‑
ry is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory,
position yourself and bystanders away from the plane of
the rotating accessory and run the power tool at maximum
no‑load speed for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment. Depending on the
application, use face shield, safety goggles or safety glass‑
es. As appropriate, wear a dust mask, hearing protectors,
gloves and a workshop apron capable of stop‑ping small
abrasive or workpiece fragments. The eye protection must
be capable of stopping flying debris generated by various
operations. The dust mask or respirator must be capable of
filtering particles generated by your operation. Prolonged ex-
posure to high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work area. Any‑
one entering the work area must wear personal protective
equipment. Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate area of op-
eration.
j) Hold the power tool by insulated gripping surfaces only
when performing an operation where the cutting acces‑
sory may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and shock the operator.
k) Position the cord clear of the spinning accessory. If you lose
control of the power tool, the cord may be cut or snagged and
your hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may catch
the surface and pull the power tool out of your control.
m) Do not run the power tool while carrying it at your side. Ac-
cidental contact with the spinning accessory could snag your
clothing, pulling the accessory into your body.
n) Regularly clean the power tool's air vents. The motor's fan
will draw the dust inside the housing and excessive accumu-
lation of powdered metal may cause electrical hazards.
o) Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution or
shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be forced in the direc-
tion opposite of the accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump toward or away
from the operator, depending on direction of the wheel's move-
ment at the point of pinching. Abrasive wheels may also break
under these conditions.
Kickback is the result of power tool misuse and/or incorrect operat-
English
15