Metabo HPT C 10FCG Manual De Instrucciones página 12

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
To process crown molding at
positions 1 and 4 in Fig. 20.
Type of Crown
Molding
Miter Angle
Setting
right 35.3°
45° Type
( mark)
right 31.6°
38° Type
( mark)
(1) Setting to cut crown moldings at positions 1 and 4 in Fig. 20 (see Fig. 21;
tilt the motor head to the left):
1 Turn the turntable to the right and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the motor head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the upper surface (Ⓐ in Fig. 19) contacts
the fence as indicated in Fig. 23.
(2) Setting to cut crown moldings at positions 2 and 3 in Fig. 20 (see Fig. 22;
tilt the head to the left):
1 Turn the turntable to the left and set the Miter Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
2 Tilt the head to the left and set the Bevel Angle as follows:
∗ For 45° type crown moldings:
∗ For 38° type crown moldings:
3 Position the crown molding so that the lower surface (Ⓑ in Fig. 19) contacts
the fence as in Fig. 24.
1
Miter angle scale
2
Fence
(Left side)
Fence
12
Bevel Angle
Setting
left 30°
( mark)
left 33.9°
( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
35.3° ( mark)
31.6° ( mark)
30° ( mark)
33.9° ( mark)
Head
Bevel angle scale
4
Fence
(Right side)
Base
Turntable
Fig. 21
Head
Bevel angle scale
3
Base
Turntable
Miter angle scale
Fig. 22
Table on base
Fig. 23
To process crown molding at positions 2
and 3 in Fig. 20.
Miter Angle
Setting
left 35.3°
( mark)
left 31.6°
( mark)
Fence
Table on base
Fig. 24
Cutting method of crown molding without tilting the saw blade.
(1) Crown molding Stopper (L) and (R) (optional accessories) allow easier
cuts of crown molding without tilting the saw blade. Install them in the
base both-sides side to be shown in Fig. 25-a. After inserting Tighten the
6mm knob bolts to secure the crown molding Stoppers.
[Optional accessories used]
• Crown molding Vise Ass'y (Include Crown molding Stopper (L))
• Crown molding Stopper (L)
• Crown molding Stopper (R)
Crown molding
vise ass'y
6mm Wing
(Optional
bolt
accessories)
6mm Wing
bolt
Crown molding stopper (L)
(Optional accessories)
6mm Wing bolt
Fig. 25-a
(2) The crown molding vise (B) (Optional accessory) can be mounted on
either left side of the fence or the right side of the fence. It can unite with
the slope of the crown molding and vice can be pressed down.
Then turn the upper knob, as necessary, to securely attach the crown
molding in position. To raise or lower the vise assembly, fi rst loosen the
6mm knob bolt.
After adjusting the height, fi rmly tighten the 6mm wing bolt; then turn
the upper knob, as necessary, to securely attach the crown molding in
position. (See Fig. 25-b)
Crown molding vise ass'y
(Optional accessories)
6mm Knob
bolt
Fence
6mm Wing bolt
Crown
molding
Fig. 25-b
Bevel Angle
Setting
left 30°
( mark)
left 33.9°
( mark)
Crown molding stopper (R)
(Optional accessories)
Knob
Crown molding stopper (L)
Crown molding stopper (R)
(Optional accessories)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

C 10fcg (s)

Tabla de contenido