How To Use - Hitachi WH 14DDL Instrucciones De Manejo

English
3. Installing the bit
Always follow the following procedure to install driver
bit. (Fig. 5)
(1) Pull the guide sleeve away from front of the tool.
(2) Insert the bit into the hexagonal hole in the anvil.
(3) Release the guide sleeve and it returns to its original
position.
(4) If you want to remove the bit, pull the guide sleeve
away from front of the tool.
CAUTION
If the guide sleeve does not return to its original
position, then the bit is not installed properly.

HOW TO USE

1. Check the rotational direction
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit
counterclockwise. (See Fig. 6) (The
are provided on the body.)
2. Switch operation
When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled.
Speed is low when the trigger switch is pulled slightly
and increases as the trigger switch is pulled more.
NOTE:
A buzzing noise is produced when the motor is about
to rotate. This is only a noise, not a machine failure.
3. Using the hook
The hook is used to hang up the power tool to your
waist belt while working.
CAUTION
When using the hook, hang up the power tool firmly
not to drop accidentally.
If the power tool is dropped, it may lead to an accident.
When carrying the power tool with hooked to your
waist belt, do not fit any bit to the tip of power tool. If
the sharp bit such as drill is fitted to the power tool
when carrying it with hooked to your waist belt, you
will be injured.
Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
(1) Removing the hook.
Remove the screws fixing the hook with Philips screw
driver. (Fig. 7)
(2) Replacing the hook and tightening the screws.
Install securely the hook in the groove of power tool
and tighten the screws to fix the hook firmly. (Fig. 8)
4. About Remaining Battery Indicator
When pressing the remaining battery indicator switch,
the red indicator lamp lights and the battery remaining
power can be checked. (Fig. 9)
When releasing your finger from the remaining
battery indicator switch, the indicator lamp changes
indication of LED light mode. The Table 4 shows the
state of red indicator lamp and the battery remaining
power.
12
State of lamp
As the remaining battery indicator shows somewhat
differently depending on ambient temperature and
battery characteristics, read it as a reference.
NOTE:
Do not give a strong shock to the switch panel or
break it.It may lead to a trouble.
L and R marks
5. How to use the LED light
By press the light selector switch on the switch panel,
the LED light mode changes as Table 5. It is indicated
by green lamp. (Fig. 10)
To prevent the battery power consumption, turn off
the LED light frequently.
Panel
display
State
CAUTION
Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your
eye will be hurt.
NOTE:
To prevent the battery power consumption caused
by forgetting to turn off the LED light, the light goes
off automatically in about 2 minutes.
6. Tightening mode selector function (Fig. 11)
CAUTION
Do not subject the switch panel to shock or damage.
Select tightening mode while the trigger switch is
released. Failure to do so could result in malfunction.
(1) Tightening mode selector switch
The rotation speed changes in 3 steps (900, 2200,
3000/3100 min
tightening mode selector switch is pressed.
S mode is suitable mode for tightening of self drilling
screw, it decrease failure of screw head breaking,
screw breaking, and screw idle running from
tightening too much screw.
Table 4
Battery Remaining Power
The battery remaining power
is enough.
The battery remaining power
is a half.
The battery remaining power
is nearly empty.
Re-charge the battery soonest possible.
Table 5
Always-ON SW interlocked
mode mode
Always ON Light only
(turn off after SW-ON
2 minute)
-1
) and select "S mode" each time the
Always-OFF
mode
Always OFF