Safety Notes; Setting The Spotlight Into Operation - IMG STAGELINE ODC-100/ WS Manual De Instrucciones

Ocultar thumbs Ver también para ODC-100/ WS:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 24
DMX LED Spotlight
Operation of the spotlight is easy for users with
basic knowledge in DMX control. However,
please read the instructions carefully prior to
operation and keep them for later reference. On
page 2, you will find the spotlights ODC-100 / WS
and PARC-100 / WS together with the menu
structure.
1 Applications
This LED spotlight is used for illumination, e. g.
on stage, in discotheques and function rooms.
The light source is a powerful white COB LED
(COB = chip-on-board technology): Many indi-
vidual LED chips are densely packed on a PCB
to provide a uniform light distribution.
The spotlight is designed for control via a
DMX light controller (3 DMX control channels),
but it can also be operated independently with-
out a controller. The ODC-100 / WS is weather-
proof (IP 66) and therefore also suited for out-
door applications.

2 Safety Notes

The spotlight corresponds to all relevant direc-
tives of the EU and is therefore marked with
WARNING The
mains voltage. Leave servicing to
skilled personnel; inexpert handling
may result in electric shock.
G
The spotlight PARC-100 / WS is suitable for in-
door use only. Protect it against dripping wa-
ter and splash water, high air humidity and
heat (admissible ambient temperature range:
0 – 40 °C).
The spotlight ODC-100 / WS is suitable for out-
door applications (admissible ambient tem-
perature range: -20 to +40 °C).
G
Immediately disconnect the mains plug from
the socket
1. if the spotlight or the mains cable is visibly
damaged,
2. if a defect might have occurred after the
spotlight was dropped or suffered a similar
accident,
3. if malfunctions occur.
In any case the spotlight must be repaired by
skilled personnel.
8
spotlight
uses
dangerous
G
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug.
G
For ODC-100 / WS only: A damaged mains ca-
ble must be replaced by skilled personnel
only.
G
No guarantee claims for the spotlight and no
liability for any resulting personal damage or
material damage will be accepted if the spot-
light is used for other purposes than originally
intended, if it is not safely installed or not cor-
rectly connected or operated, or if it is not re-
paired in an expert way.
If the spotlight is to be put out of oper-
ation definitively, take it to a local recy-
cling plant for a disposal which is not
harmful to the environment.
3 Setting the Spotlight
into Operation
3.1 Installation
G
Always position the spotlight in such a way to
ensure sufficient air circulation during opera-
tion. Never cover the cooling fins of the hous-
.
ing.
G
Always keep a minimum distance of 50 cm to
the illuminated object.
WARNING When the spotlight is installed at a
place where people may walk or sit
under it, additionally secure it, e. g.
via a safety rope. Guide the safety
rope through the eyebolt on the rear of the
spotlight and fasten it in such a way that the
maximum falling distance of the spotlight will
not exceed 20 cm.
1. Install the spotlight via its mounting brackets,
e. g. with a stable mounting screw or a sup-
port for lighting units (C hook) on a cross bar.
To align the spotlight, release the two
locking screws of the mounting brackets.
Adjust the desired inclination of the spotlight
and fasten the screws.
2. Alternatively, set up the spotlight on its own:
Fold out the mounting brackets underneath
the spotlight and use them as a stand. Then
fasten the locking screws.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Parc-100/ ws38.710038.7130

Tabla de contenido