Tabla de contenido
Publicidad
Primera edición • Segunda impresión
Señales de seguridad
y ubicaciones
31060
97890
82677
82677
82677
DANGER
Tip-over Hazard
Failure to replace tires with tires
of same specification will result
in death or serious injury.
Tires are critical to machine
stability.
Do not replace factory-installed
tires with high flotation tires.
Only replace factory-installed tires
with tires of same specification and
ply rating. Tire Size:355/55 D625,
14 ply
27564
DANGER
Electrocution Hazard
Death or injury can result from contacting electric
power lines.
Always contact the electric power line owner. The
electric power shall be disconnected or the power
lines moved or insulated before machine operations
begin.
27564 C
114258
31060
DANGER
Burn Hazard
No smoking. No
Fuel and fumes
flame. Stop
can explode
engine.
and burn.
114258 A
N° de pieza 114303SP
114258
27564
28177
Tire Pressure:
70 psi / 4.92 bar
Lug Nut Torque:
Dry bolts:
170 ft-lbs /
225 Nm
Lubricated bolts:
130 ft-lbs /
176 Nm
82677 C
Maintain required clearance.
Line Voltage
Required Clearance
0 to 300V
Avoid Contact
300V to 50KV
10 ft
3.05 m
50KV to 200KV
15 ft
4.60 m
200KV to 350KV
20 ft
6.10 m
350KV to 500KV
25 ft
7.62 m
500KV to 750KV
35 ft
10.67 m
750KV to 1000KV
45 ft
13.72 m
DANGER
Tip-over Hazard
Altering or disabling limit switches
can result in machine tip-over.
Machine tip-over will result in
death or serious injury.
Do not alter or disable limit switch(s).
31060 B
S-60 High Capacity
28161
97890
WARNING
Crush Hazard
Improper Use Hazard
Death or serious
The operator is responsible for safe machine
operation. This includes:
injury may result
1Avoid hazardous situations.
2Always perform a pre-operation inspection.
from platform
3Always perform function tests prior to use.
crushing
4Inspect work place.
5Only use the machine as it was intended.
personnel
Do not operate unless:
against boom.
You read, understand and obey:
Keep away from
You are properly trained to safely operate this machine.
path of moving
Electrocution Hazards
platform.
28177 C
Tip-over Hazards
Do not raise or extend boom unless
machine is on firm, level ground.
Do not depend on tilt alarm as a
level indicator. Tilt alarm sounds in
platform only when machine is on a
severe slope.
Do not raise boom when wind speeds
may exceed 28 mph / 12.5 m/s.
Do not operate machine in strong or
gusty winds. Do not increase surface
area of platform or load. Increasing
area exposed to wind will decrease
machine stability.
Do not drive machine on or near uneven terrain, unstable
surfaces or other hazardous conditions with boom raised
or extended.
28161
Do not drive machine on a slope that exceeds the
maximum slope or side slope rating for the machine.
Use extreme care and slow speeds while driving the
machine in stowed position across uneven terrain,
debris, unstable or slippery surfaces and near holes
WARNING
and drop-offs.
Do not attempt to free a caught or snagged platform
using platform controls. All personnel must be removed
from platform before attempting to free platform using
ground controls.
Crush Hazard
Contact with moving parts can
result in death or serious
injury.
Keep away from moving parts.
28161 C
Manual del operario
Seguridad general
DANGER
Do not alter or disable machine components that in any
way affect safety and stability.
Do not push off or pull toward any
object outside of the platform.
Do not place or attach overhanging
loads to any part of this machine.
Do not place ladders or scaffolds in
platform or against any part of this
machine.
Do not use machine on a moving or mobile surface or
vehicle.
Be sure all tires are in good condition, air-filled tires are
- manufacturer's instructions and safety rules —
properly inflated and lug nuts are properly tightened.
safety and operator's manuals and decals
Fall Hazards
- employer's safety rules
- applicable governmental regulations
Occupants must wear a safety
belt or harness in accordance
with governmental regulations.
Attach lanyard to anchor
provided in platform.
This machine is not electrically
Do not sit, stand or climb on
insulated and willnot provide
the platform guard rails.
protection from contact with or
Maintain a firm footing on the
proximity to electrical current.
platform floor at all times.
Minimum Safe Approach Distance
Do not climb down from the
Voltage
Distance
platform when raised.
Phase to Phase
Feet Meters
Lower the platform entry mid-
0 to 300V
Avoid Contact
rail or close the entry gate
300V to 50KV
103.05
before operating.
50KV to 200KV
154.60
200KV to 350KV206.10
Collision Hazards
350KV to 500KV257.62
Be aware of limited sight distance and blind spots when
500KV to 750KV
3510.67
driving or operating.
750KV to 1000KV
4513.72
Check work area for overhead
obstructions or other possible
hazards.
Be aware of crushing hazard
when grasping the platform guard
rail.
Observe and use color-coded
direction arrows on the platform
controls and drive chassis for
drive and steer functions.
Do not lower the boom unless the area below is clear of
personnel and obstructions.
Explosion Hazard
Do not start engine if you smell or detect liquid
petroleum gas (LPG), gasoline, diesel fuel or other
explosive substances.
Do not refuel the machine with the engine running.
Damaged Machine Hazards
Do not use a damaged or malfunctioning machine.
Be sure all maintenance has been performed as
specified in the appropriate operator's and service
manuals
Be sure all decals are in place and legible.
Be sure safety, operator's and responsibilities manuals
are complete, legible and in the storage container
located on the platform.
28177
97890 A
5
Publicidad
Tabla de contenido
