Conformity And Approval; Connecting And Switching On The Receiver; Setting The Transmission Channel - IMG STAGELINE TXS-606 Manual De Instrucciones

as for musicians and live performances on stage .
The True Diversity* receiver uses the UHF range
672,000 – 696,975 MHz .
* True Diversity technology: The signal sent from the
wireless microphone is received by two antennas and
amplified in two separate receiver sections . The signal
of the highest power is then processed .
Frequency setting via the ACT function (Automatic
Channel Targeting) is a most convenient feature:
Simply press a button to set the wireless microphone
via IR signal to the channel selected on the receiver .
3.1 Accessories
The following wireless microphones from IMG
STAGELINE can be used together with the TXS-606:
Item Type
TXS-606DT/ 2 Wireless desktop microphone
Pocket transmitter for microphones
TXS-606HSE / 2
with 3-pole mini XLR plug
TXS-606HT/ 2 Hand-held wireless microphone
Pocket transmitter
TXS-606LT/ 2
with tie-clip microphone
The wireless microphones use the frequency range
672 .000 – 691 .975 MHz .

3.2 Conformity and approval

Herewith, MONACOR INTERNATIONAL declare that
the product TXS-606 complies with the directive
2014 / 53 / EU . The EU declaration of conformity is
available on the Internet:
www .img-stageline .com
Restrictions or requirements apply in the fol-
lowing countries:
CZ DE
IT LT
The regulations of the country where the product
is operated must always be observed . Prior to op-
erating the product, please contact the MONACOR
subsidiary or the corresponding authorities of the
respective country . Links to the national authorities
can be found via the following Internet address:
www .cept .org
t ECC
t Topics
t Other spectrum topics: SRD Regulations and
indicative list of equipment sub-classes
t EFIS and National Frequency Tables
EL FI FR
MT PL
4 Operation
4.1 Connecting and switching on the receiver
1) Connect the receiving antennas (2) provided to
the antenna jacks ANT A and ANT B (13) . To lock
the antennas, turn the knurled ring of the plug
clockwise to the stop . Then set the antennas to
a vertical position .
To remove the antennas later, turn the ring
counter-clockwise first to unlock it .
2) Connect the receiver to the subsequent unit (e . g .
amplifier, mixer) . For this purpose, two audio
outputs are provided:
– MIC OUT (10) as an XLR jack, balanced
to connect a microphone input
– LINE OUT (12) as a 6 .3 mm jack, unbal .
to connect an input with line level; the output
level is adjustable (
3) Connect the power supply unit provided to the
power supply jack DC INPUT (9) and to a mains
socket (230 V/ 50 Hz) .
4) To switch on the receiver, press the button
POWER (8) until the display (3) lights up .
To switch off the receiver, press the button
until the display shows OFF . If the receiver is not
in use for a longer period of time, disconnect the
power supply unit of the receiver from the mains
socket; even with the receiver switched off, the
power supply unit has a low power consumption .

4.2 Setting the transmission channel

Scan a free transmission channel automatically or
set it manually . Then simply press a button to set
the wireless microphone via IR signal to the same
channel .
The wireless microphones TXS-606... / 2 operate
in a smaller frequency range; therefore, it is not
pos sible to use the channel groups 08 and 09 .
1) To automatically scan a free receiving channel,
keep the button ACT (7) pressed until the display
indicates the scan mode (
riod of time, the display will show the number of
the channel found . The corresponding frequencies
can be found in the table on pages 24 / 25 .
2) To manually set a specific transmission fre-
quency, see the table on pages 24 / 25 for
the corresponding channel group and channel
number .
a) Press the button SET (4) once: The digits for
GROUP will start flashing on the display .
b) As long as the digits keep flashing (for a few
seconds after the button SET,  or  was
☞ chapter 4 .3)
) . After a short pe-
9