Use Of Hob User Instructions; Using The Gas Burner; Maintenance And Cleaning; Aftercare - Hoover HF7 Manual De Instrucciones

3. USE OF HOB USER INSTRUCTIONS

This appliance must only be used for the purpose for which it is
intended, domestic cooking, and any other use will be considered
improper and could therefore be dangerous. The Manufacturer will
not be responsible for any damage or loss resulting from improper
use.

3.1. USING THE GAS BURNER

For ignition simply push in and turn the knob to the ignition symbol.
If the burners have not been used for a couple of days, wait for a
few seconds before lighting the burner, this will allow any air
present in the pipes to escape.
The ignition system will start to generate spark. When the flame
will light, keep the knob pressed in for 5 or 6 seconds more than
rotate the Knob to the minimum position to switch off the ignition
system, than regulate the power of the flame. Figure 7
A
IGNITION
OFF
If the burner does not ignite within 3 seconds, or is accidentally
extinguished, turn the knob to the 0 position, wait one minute, and
repeat the operation.
ATTENTION:
Prior to switching on the gas hob ensure that the burners and burner
caps are correctly placed within their position.
GENERAL ADVISE
For best results, use cooking vessels with a flat surface. The size of
the surface should match the gas burner size as follows.
Table A
Burner Type
A
Auxiliary Burner
R front Rapid Burner
R back
Rapid Burner
UR
Ultra Rapid Burner
Burner Type
A Auxiliary Burner
R
Rapid Burner
UR
Ultra Rapid Burner
For burners Lay-out see Pag 47
Don't use pan or pot that go out of the maximum dimensions of the
product.
For smaller containers the gas burner should be regulated so that the
flame does not overlap the base of the pan. Vessels with a concave or
convex base should not be used.
WARNING: If a flame is accidentally extinguished, turn the knob
to the off position and do not attempt to re-ignite if for at least 1
minute.
If over the years the gas taps become stiff to turn it is necessary to
lubricate them.
Such operation must be carried out only by qualified Service
Engineers.
B C
MAX
OFF
IGNITION
75 cm 4 gas
Ø pan / pot (cm)
8 - 18
18 - 26
18 - 22
18 - 22
90 cm 3 gas
Ø pan / pot (cm)
8 - 18
18 - 26
18 - 26

4. MAINTENANCE AND CLEANING

Before cleaning the hob, ensure the appliance has cooled down.
Remove the plug from the socket or (if connected directly) switch off
the electricity supply.
Never use scouring pads, sharp objects, abrasives, corrosive
detergents, bleaching agents or acids. Avoid any acid or alkaline
substances (lemon, juice, vinegar Etc.) on the enamelled, varnished
or stainless steel sections.
The burners can be cleaned in dishwasher and the plate with soapy
water.
It is important the Burners are replaced correctly.
Figure 7
D
MIN
!

5. AFTERCARE

Before calling out a Service Engineer please check the following: 
that the plug is correctly inserted and fused;
 that the gas supply is not faulty.
If the fault cannot be detected: Switch off the appliance and call the
After Service Centre. DO NOT TAMPER WITH THE APPLIANCE.

6. PROTECTION OF THE ENVIRONMENT

Individuals can play an important role in ensuring that WEEE does not
become an environmental issue; it is essential to follow some basic
rules:
• WEEE shall not be treated as household waste.
• WEEE shall be handed over to the relevant collection points
managed by the municipality or by registered companies. In many
countries, for large WEEE, home collection could be present.
• When you buy a new appliance, the old one may be returned to the
retailer who has to collect it free of charge on a one-to-one basis, as
long as the equipment is of equivalent type and has the same
functions as the supplied equipment.
07 GB - IE
This appliance is marked according to the European
directive 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE). WEEE contains both
polluting substances (which can cause negative
consequences for the environment) and basic
components (which can be re-used). It is important to
have WEEE subjected to specific treatments, in order
to remove and dispose properly all pollutants, and
recover and recycle all materials.
Figure 8