Customer Service; Battery Warnings - Peg-Perego CORRAL T-REX Guía De Uso Y Mantenimiento

DISPOSAL OF THE BATTERY
• Help protect the environment.
• Used batteries must not be disposed of with
domestic waste.
• They can be left at a used battery or special waste
collection centre. Contact your local authorities
for more information.

BATTERY WARNINGS

Battery charging must be carried out and supervised
by adults only.
Do not allow children to play with the battery.
CHARGING THE BATTERY
• Charge the battery according to the instructions
enclosed with the battery charger and never for
more than 24 hours.
• To avoid damage, the battery should be charged as
soon as the vehicle starts to lose speed.
• If the vehicle is left unused for a long time,
remember to charge the battery and to keep it
disconnected from the electrical system. Repeat the
recharge procedure at least once every three
months.
• The battery must not be charged upside-down.
• Do not forget about the battery which is being
charged! Check it from time to time.
• Only use the battery charger provided and the
original PEG PEREGO battery.
• The battery is sealed and does not require
maintenance.
• Do not remove the battery charger from the
socket by pulling the cable.
• Do not move the toy by pulling the battery charger
cable.
• Do not cover the battery charger cable, as this
would cause it to overheat.
• Do not place the cable and/or battery on hot
surfaces.
• Take care on how and where you wrap the cable to
so as not to damage it or compromise its
operation.
WARNING
• THE BATTERY CONTAINS CORROSIVE TOXIC
SUBSTANCES.
DO NOT TAMPER WITH IT.
• The battery contains acid-based electrolytes.
• Do not create direct contact between the battery
terminals, avoid strong impacts: risk of explosion
and/or fire.
• While charging, the battery produces gas. Charge
the battery in a well-ventilated environment, away
from sources of heat and flammable materials.
• The flat battery must be removed from the vehicle.
• It is not advisable to bring the battery into contact
with clothes, as it could damage them.
• Only use batteries or accumulators of the
recommended kind.
IF THERE IS A BATTERY LEAK
Protect your eyes. Avoid direct contact with the
electrolyte. Protect your hands.
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the toy
before carrying out cleaning, maintenance, or any
type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

CUSTOMER SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
THE VEHICLE MUST BE ASSEMBLED BY ADULTS.
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE PACKAGING.
ALL THE NECESSARY SCREWS AND SMALL
COMPONENTS ARE STORED IN A BAG INSIDE
THE PACKAGING.
THE BATTERY MAY ALREADY BE INSTALLED.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • FITTING THE FRONT WHEELS: Prepare 2 of
the 4 wheels, inserting a hexagonal bushing on
the inner side of each wheel. From the opposite
side, press a rim into place for each wheel.
2 • Remove the steering lever protection caps.
3 • Insert the following elements in sequence onto a
steering lever: 1 large metal washer, the wheel,
and 1 small metal washer.
4 • Insert a nut and secure the wheel using the tool
supplied. Proceed in the same way for the other
front wheel.
5 • FITTING THE REAR WHEELS: Press the 2 round
elements (drivers) into place in the wheels, as
shown in the figure, and press the rims in place
into the outer part of the wheels.
6 • Take the axle out of the packaging and remove
the protective caps. Insert the axle into the rear
part of the vehicle, as shown in the figure.
7 • Insert 1 wheel, 1 small washer, and 1 nut from
each side of the axle, in this order. Fasten the
wheels using the 2 keys provided to tighten the 2
nuts simultaneously, as shown in the figure.
If the axle comes out of the wheels, insert a
plastic washer after the wheel. Make sure to
insert it in the right direction, as shown in detail
A.
8 • Press the 4 hubcaps into place.
9 • Insert the gear shift lever into its housing, until it
snaps into place.
10 • Place the bumper at the front of the vehicle,
inserting the tab into its housing.
11 • Fasten the bumper.
12 •Position and secure the fairing.
13 • Insert the grips until reaching the end stop,
taking care that the notches engage properly.
14 • Connect the 2 handlebar connectors. Pay
attention to the insertion of cables in place,
before installing the handlebar.
15 • Insert the handlebar unit into the steering
column, pulling it upwards to ensure that the 2
holes correspond, as shown in the figure.
16 • Tighten.
17 • Insert the mudguard flap, taking care that the 2
hooks are fully engaged.
18 • Insert the screw into the hole and tighten the
flap. Proceed the same way for the other flap.
19 • Connect the exhaust pipe inserting the tab A in
the bodywork hole.
20 • Fix the exhaust pipe with the screw supplied. Do
the same for the other pipe.
21 • Insert the antenna into its opening and push in
place.
22 • Rotate the red lock behind the saddle and bring
it to the position shown in the figure. A: the
saddle is locked; B: the saddle can be opened.
23 • Press the rear part of the bodywork down, to
facilitate the opening of the saddle. Lift the
saddle.
24 • Connect the plugs. When you have finished,