Freeman PFN1564 Manual Del Usuario página 5

MODEL: PFN1564
WARNING:
!
Always unload all fasteners before removing
tool from service.
WARNING:
!
Always disconnect the air source before
unloading.
CLEARING JAMS
Occasionally, a fastener may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
1 . Disconnect the tool from air source.
Remove fasteners from the tool. Failure to do
2 .
so will cause the fasteners to eject from the front
of the tool.
⒊ Pull and open the jam release(D).
⒋ Using caution not to bend or damage the driver
blade, using pliers or a screwdriver if required to
clear the jammed fastener.
⒌ Close the jam release(D).
⒍ Reconnect the tool to the air source.
⒎ Reload the tool with fasteners.
Jam release(D)
WARNING:
!
Make sure there is no fastener in
magazine before clearing a jam.
07
.
HTTP://WWW FREEMANTOOLS COM
WARNING:
!
Disconnect the tool from the air source
whenever clearing a jam. After
disconnecting the tool from the air
compressor, there should still be enough
air pressure to fire the tool. After the air
hose is disconnected, always fire the tool
into scrap wood repeatedly to make sure
all of the compressed air is expended.
NO-MARRING PAD
The no-marring pad attached the nose of the tool
helps prevent marring and denting when working
with softer woods.
WARNING:
!
Disconnect the tool from the air source
before removing or replacing the no-
marring pad or replacing the no-marring
pad. Failure to do so could result in serious
personal injury.
SETTING THE AIR PRESSURE
The amount of air pressure required depends on
the size of the fasteners and the workpiece material.
Begin testing the depth of drive by driving a test nail
into the same type of workpiece material used for
the actual job.
Drive a test fastener with the air pressure set at 90-
95psi. Raise or lower the air pressure to find the
lowest setting that will perform the job with
consistent results.
It may be possible to achieve the desired depth with
air pressure adjustments alone.
DEPTH ADJUSTMENT
The driving depth of the fasteners are adjustable.
To adjust the depth, use the drive depth adjustment
wheel(E) on the tool.
1 . Disconnect the tool from the air source.
Turn the depth wheel left or right to change the
2 .
driving depth.
⒊ Reconnect the tool to the air source.
⒋ Drive a test nail after each adjustment until the
desired depth is set.
.
1-888-669-5672
MODEL: PFN1564
Adjustment wheel(E)
CAUTION:
It is advisable to test the depth on a scrap
workpiece to determine the required
depth for the application.
To determine depth of drive, first adjust
the air pressure and drive a test fastener.
Never exceed 120 psi.
FIRING THE TOOL
(USING THE SELECTABLE TRIGGER)
The tool is with a selectable trigger set in the single
sequential actuation mode. The selectable trigger
can also be set for contact actuation mode.
SINGLE SEQUENTIAL ACTUATION MODE
Single sequential actuation provides the most
accurate fastener placement.
Disconnect the tool from the air source.
1 .
Rotate the selector to one single nail position(F).
2 .
⒊ Reconnect the tool to the air source.
⒋ Grip the tool firmly to maintain control. Position
the nose of the tool onto the work surface.
⒌ Push the tool against the work surface to
depress the workpiece contact.
⒍ Squeeze the trigger to drive a fastener.
CONTACT ACTUATION MODE
Contact actuation allows for very fast, repetitive
fastener placement.
1 . Disconnect the tool from the air source.
2 . Rotate the selector to two nails position(G).
⒊ Reconnect the tool to the air source.
⒋ Grip the tool firmly to maintain control. Position
the nose of the tool onto the work surface.
⒌ Squeeze and hold the trigger, push the tool
against the work surface to depress the
workpiece contact and drive a fastener.
.
HTTP://WWW FREEMANTOOLS COM
In the contact actuation mode, the tool may also be
operated by depressing the workpiece contact
against the surface and squeezing the trigger.
Two nails position(G)
Single nail position(F)
WARNING:
!
During normal use the tool will recoil
immediately after driving a fastener. This
is a normal function of the tool. Do not
attempt to prevent the recoil by holding
the tool against the work. Restriction to
the recoil can result in a second fastener
being driven from the tool. Grip the
handle firmly and let the tool do the work.
Failure to heed this warning can result in
serious personal injury.
MAINTENANCE
WARNING:
!
Any time inspection, maintenance, and
cleaning are done:
◆Disconnect the tool from the air source.
◆ Empty the magazine completely.
ANTI-DUST CAP
Each tool is packed with an anti-dust cap on the air
connector.
Keep the anti-dust cap cover the air connector
when the tool is not in use.
LUBRICATION
The tool is uniquely designed not to need daily
lubrication. But lubrication is required for best
performance after long periods use. Oil for
pneumatic fastening tools is added through the air
line connection and will lubricate internal parts. Do
not use detergent oil or additives as these lubricants
will cause accelerated wear to the seals and
bumpers in the tool, resulting in poor tool
performance and frequent tool maintenance.
.
1-888-669-5672
08