Victron energy Quattro 12/5000/200 Manual De Instrucciones página 25

5.5.2 Step 2: Other settings
The remaining settings are not relevant for slaves.
Some of the remaining settings are not relevant for followers (L2, L3). These settings are imposed on the whole system by the
leader L1. If a setting is irrelevant for L2, L3 devices, this is mentioned explicitly.
ds8-ds7: Setting charging voltages (not relevant for L2, L3)
Absorption Float
ds8-ds7
voltage voltage
14.1 13.8
off off 28.2 27.6
56.4 55.2
14.4 13.8
off on 28.8 27.6
57.6 55.2
14.7 13.8
on off 29.4 27.6
58.8 55.2
15.0 13.8
on on 30.0 27.6
60.0 55.2
ds6: absorption time 8 or 4 hours (not relevant for L2, L3)
ds5: adaptive charging characteristic (not relevant for L2, L3)
ds4: dynamic current limiter
ds3: UPS function
ds2: converter voltage
ds1: converter frequency (not relevant for L2, L3)
(the wide input frequency range (45-55Hz) is 'on' by default)
Step 2: Exemplary settings for stand-alone mode
Example 1 is the factory setting (since factory settings are entered by computer, all DIP switches of a new product are set to
'off' and do not reflect the actual settings in the microprocessor).
DS-8 Ch. voltage off
DS-7 Ch. voltage on
DS-6 Absorpt. time on
DS-5 Adaptive ch. on
DS-4 Dyn. Curr. limit off
DS-3 UPS function: on
DS-2 Voltage on
DS-1 Frequency on
Step 2
Example 1 (factory setting):
8, 7 GEL 14,4V
6 Absorption time: 8 hours
5 Adaptive charging: on
4 Dynamic current limit: off
3 UPS function: on
2 Voltage: 230V
1 Frequency: 50Hz
To store the settings after the required values have been set: press the 'Down' button for 2 seconds (lower button to the right of
the DIP switches). The temperature and low-battery LEDs will flash to indicate acceptance of the settings.
You can then leave the DIP switches in the selected positions, so that the 'other settings' can always be recovered.
Storage
Suitable for
voltage
13.2 Gel Victron Long Life (OPzV)
26.4 Gel Exide A600 (OPzV)
52.8 Gel MK battery
Gel Victron Deep Discharge
13.2
Gel Exide A200
26.4
AGM Victron Deep Discharge
52.8
Stationary tubular plate (OPzS)
AGM Victron Deep Discharge
13.2
Tubular plate (OPzS) batteries in
26.4
semi-float mode
52.8
AGM spiral cell
13.2
Tubular plate (OPzS) batteries in
26.4
cyclic mode
52.8
DS-8 off DS-8
DS-7 off DS-7
DS-6 on DS-6
DS-5 on DS-5
DS-4 off DS-4
DS-3 off DS-3
DS-2 on DS-2
DS-1 on DS-1
Step 2 Step 2
Example 2: Example 3:
8, 7 OPzV 14,1V 8, 7 AGM 14,7V
6 Absorption time: 8 h 6 Absorption time: 8 h
5 Adaptive charging: on 5 Adaptive charging: on
4 Dyn. current limit: off 4 Dyn. current limit: on
3 UPS function: off 3 UPS function: off
2 Voltage: 230V 2 Voltage: 240V
1 Frequency: 50Hz 1 Frequency: 50Hz
on = 8 hours off = 4 hours
on = active off = inactive (fixed absorption time)
on = active off = inactive
on = active off = inactive
on = 230V / 120V off = 240V / 115V
on = 50Hz off = 60Hz
on DS-8 on
off DS-7 on
on DS-6 off
on DS-5 off
on DS-4 off
off DS-3 on
off DS-2 off
on DS-1 off
Step 2
Example 4:
8, 7 Tubular-plate 15V
6 Absorption time: 4 h
5 Fixed absorption time
4 Dyn. current limit: off
3 UPS function: on
2 Voltage: 240V
1 Frequency: 60Hz
21