Introduction; Intended Use; Indications For Use; Contraindication - DeVilbiss Healthcare IntelliPAP AUTOADJUST CPAP DV54 Serie Guía De Instrucciones

• Never rinse or place the device in water. Never allow liquids to get into or around any of the ports, switches or air
filter; doing so will result in device damage. If this occurs, discontinue use and remove the power cord from the
power source. Allow the device to completely dry before use.
• Do not place the IntelliPAP where it can be knocked onto the floor or where the power cord may create a trip hazard.
• Only the DeVilbiss DV5 series Heated Humidifier system is recommended for use with the IntelliPAP. Other
humidifier systems may prevent the device from detecting snoring and may cause inappropriate pressure levels in
the mask.
• Empty and dry humidifier water chamber before transporting.

iNtroDuctioN

intended use

The DeVilbiss IntelliPAP Model DV54 Series AutoAdjust is intended for use in treating OSA in spontaneously breathing
patients 30 Kg (66 lbs) and above by means of application of positive air pressure. The device is to be used in home and
clinical environments.
indications For use (optional Heated Humidifier)
Use on the advice and prescription of a licensed physician to help relieve the symptoms of dryness of the throat, nasal
passages and the mouth, which are common with positive airway pressure therapy. This is especially true in dry climates
and during the cold season when humidity in the air is typically lower than at other times.

contraindication

Do not use IntelliPAP system if your upper airway has been bypassed.
NOTE–Symptoms of dryness of the throat, nasal passages, and the mouth are common with positive airway pressure
therapy. The IntelliPAP features an optional humidifier system to help minimize these effects.

KeY Features

DeVilbiss intellipap Device
and B)
1. Keypad/LCD Display (see Figure C)
2. Air Supply Port on Back
3. Air Supply Port on Bottom (for optional humidifier)
4. Air Supply Port Plug
5. Heater Power Connector (for optional humidifier)
6. AC Power Connector
7. DC Power Connector
8. Data Port
9. Power Cord (appropriate to your wall outlet) (not
shown)
10. Air Inlet Filter Opening
11 Connector Cover (not shown)

Keypad

(Figure c)
1. On/Off
2. Previous Item
3. Next Item
4. Delay
5. Decrease Value
6. Increase Value
7. Heater Power LED (for optional humidifier)
Ask your equipment provider for information about other
DeVilbiss masks, equipment, and accessories.

sYsteM asseMBLY

Without Heated Humidification

1. Locate the air supply port and heater power connector on the bottom of the IntelliPAP device. Ensure that each
opening has the appropriate soft cover securely attached.
2. Place the IntelliPAP on a stable surface such as a nightstand or table. If you wish, you may also place the device on
the floor at the bedside, being careful to place the unit where it won't be kicked or stepped on. Ensure that the air
inlet in the back of the device is not blocked by anything such as curtains or bedding.
NOTE
Never place the IntelliPAP system on a soft surface such as a bed or couch during operation.
–
A-DV54
(page 2, Figures a-F)
(Figures a

Humidifier cradle

1. Heater plate
2. Heater power connector
3. Storage compartment for connector cover (on
bottom)
4. Air supply port inlet
5. Air supply port outlet
6. Flow generator release button
7. Flow generator locking tabs

Water chamber

1. Chamber lid
2. Chamber base
3. Heat transfer plate (on bottom)
4. Sealing gasket
5. Water level indicators (front and sides)
6. Chamber release latch
7. Chamber disassembly lever

therapy Management system

1. SmartLink (optional)
®
(Figure D)
(Figure e)
(Figure F)
eN - 5