Stanley FATMAX SFMCD710 Traducido De Las Instrucciones Originales página 7

Ocultar thumbs Ver también para FATMAX SFMCD710:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 43
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured in
accordance with a standard test method provided by EN60745
and may be used for comparing one tool with another. The
declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
:
Warning! To reduce the risk of injury, the user
f
must read the instruction manual.
Wear ear protectors with impact drills. Exposure
to noise can cause hearing loss.
Additional safety instructions for batteries
and chargers
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the tool.
u
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Chargers
Use your STANLEY FATMAX charger only to charge
u
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
u
Have defective cords replaced immediately.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
(Original instructions)
$
+
The charger is intended for indoor use only.
Read the instruction manual before use.
Do not attempt to charge damaged batteries.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
If the supply cord is damaged, it must be replaced by
u
the manufacturer or an authorised STANLEY FATMAX
Service Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the
u
new plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Features
This appliance includes some or all of the following features.
1. Trigger Switch
2. Forward/Reverse Button
3. Torque Adjust Collar
4. Dual Range Gear Selector
5. Keyless Chuck
6. Battery
7. LED Work Light
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (Fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
ENGLISH
7

Publicidad

Tabla de contenido
loading

Tabla de contenido