Multiplex Gemini 33 2634 Manual De Instrucciones página 4

!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The "Gemini" power set, # 33 2634, is a high-
performance brushless motor system at a reasonable
price, designed for aerobatic models with an all-up weight
of up to 900 g, such as our Gemini biplane. Flight times
will be up to twelve minutes if the recommended battery is
used.
2. C / R
ONTENTS EPLACEMENT PARTS
• 1 Himax C 2816-0890 motor
• 1 MULTIcont BL-27/II speed controller
• 1 10" x 5" propeller
• 1 propeller driver and nut for ELAPOR spinner
• Various small items for installation in the model
Options:
• ELAPOR 62 mm Ø spinner incl. Holder
• Propeller driver and spinner for motors with 4 mm Ø shaft,
prop bore 6 mm
3. T . O
YP PERATIONAL
P S "G
OWER ET
3S LiPo / 10" x 5" prop
Recommended Battery:
MULTIPLEX Li-BATT BX 3/2100
MULTIPLEX Li-BATT BX 3/2500
If you use the Himax C 2816-0890 motor and the stan-
dard propeller supplied in the set, do not use more than a
3S LiPo pack or 9 NiXX cells
4. S N
AFETY OTES
The power set "Gemini" is designed exclusively for use in
modelling applications. Incorrect use can result in serious
personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the pro-
peller
•
Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for Power Set „Gemini"
D
ATA OF
"
EMINI
Current drain: approx.13.0 A
# 15 7131
# 15 7191
.
5. A
SSEMBLING
P
OWER
Spinner holder
(included in Gemini kit)
# 33 3016
ELAPOR spinner
# 7 2275
(included in Gemini kit)
# 73 3106
# 33 2325
1. Screw the motor to the motor mount
motor is free to rotate. When deploying the motor
cables, check that they cannot make contact with the
# 22 4207
spinning motor. Secure the motor leads with Velcro
tape or similar.
# 33 2314
2. Fit the split taper collet and the propeller driver on the
motor shaft.
3. Fit the propeller and the spinner holder on the propeller
driver, and secure them with the nut for the ELAPOR
spinner (supplied).
4. Clip the ELAPOR spinner onto the spinner holder.
6. I
NITIATION OF THE
P
OWER
1. Connect the three wires attached to the speed control-
ler to the three wires attached to the motor; the order of
connection is unimportant.
2. Locate the UNI connector attached to the speed con-
troller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking for-
ward. If this is not the case, disconnect the flight battery
and swap over any two of the three motor wires.
6. Switch off the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
O T
F HE
S "G "
ET EMINI
Split taper
collet
Propeller driver
ELAPOR spinner nut
S "G "
ET EMINI
ensure that the
Page 1/2