General Features; Accessories Included - Televes OSB48S Manual De Usuario

Introduction
The Main indoor cabinet, ref.233003 has been designed to cover the
different needs that may arise in FTTH (Fiber To The Home) or FTTR
(Fiebr To The Room) installations. In both, the register is endowed with
two independent compartiments which allow the operators network to
become independent of the user`s/subscriber`s network. With up to 48
SC/ APC adapters capacity (not included) it allows to cover the needs of
the F.O. networks (apartment building, hotel resorts...)
It possess the feature of being vertically stackable, with intercommunication
between the different registers, it allows to enlarge the services based on
the needs of each type of instalaltion.
Internally it disposes of two compartiments:
- The left one, designed for the access to the F.O. hoses that belong to the
propierty (users) and with capacity for stowage the fusions.
- The right one, designed to administrate the fibers coming from the ope-
rators (according to use or needs, these assignements can be reversed).
Both compartiments are divided by a panel with up to 48 optic adapters
SC/SPC Ref. 233203 (not included) capacity, that act as a point of union
between operator`s network and the building/user´s network (in FTTH
installations). In FTTR networks, this panel will allow to connect the diffe-
rent optic fibers that will hand the service to the rooms (ONTs and ONUs),
through the insertion of one or several fiber optic splitters.
The reight compartiment, has two inputs (a bottom one and an upper
one), which will allow the access of the operators (FTTH networks) or
the output of the different F.O. to the rooms (FTTR networks). In case of
vertical mountage of several registers, this compartiment will permit the
intercommunication between them (erase the rubbers that act as a fiber
pass to facilitate the mountage of multiple registers).

General features

Two independent compartments with hinged doors. The left one with
lock and the right one with mechanical lock.
Separator panel with up to 48 adapters SC/APC (Ref.233203)capacity.
Incorporates 2 independent and folding F.O trays (book format), for
stowage up to 24 fusions in each one of them.
F.O trays installed upon the left door, thus allowing the installer to work
the fibers upon an horizontal surface (results in a greater comfort of
installation).
Removable fiber holder (which eases the manipulation) for the ancho-
rage of the different F.O. hoses that access the left compartiment. Dis-
poses of 4 metallic anchors for the attachment of the central element
of resistance that the fibers possess, as well as 8 anchor points of the
fibers to the support by flanges.
Incorporates 8 adhesive flanges (fiber-fastener) to ease the guidance of
the fibers through the interior of the register.
The register, in its upper part disposes of:
- 1 adjustable rubber (Ø max. 48 mm) for the pass of the fibers towards a
top register, either for the input or the output of fibers.
- 2 anchors for top mounting of another register.
The register, in its bottom part disposes of:
- 1 adjustable rubber (Ø max. 48 mm) for the pass of the fibers towards a
lower register, either for the input or the output of fibers.
- 2 anchors for the lower mounting of another register.
On its left part disposes of:
- 1 access / output for optic fibers, with dimensions of 83mm (Width) x
34mm (Height). Includes a brush to prevent dust access.
Dimensions ((Width x Height x Depth): 444 × 180 × 125 mm.
Register colour: RAL 7035.
Weight : 3,1 Kg.

Accessories included:

2 Rubbers for the fiber pass of 50 mm.
2 Cannulas for the fiber grouping.
8 Flanges.
8 Fiber fastener adhesive flanges.
1 Velcro coil for the trays.
4 Joint stowages, each one of them with up to 12 fusions capacity.
4 Wall plugs, 4 screws and 4 washer for for the installation of the regis-
ter in the wall.
1 Label for identification of the F.O. connectors in base of its location.
Main indoor cabinet installation
1. Before screwing the main indoor cabinet on the wall, locate it having
in mind the free space needed for working comfortably. Afterwards, fix
the register to the wall (by means of the screws included) trough the
points indicated in the following image:
Wall anchorage points
2.
If you want to install multiple main indoor cabinet jointly, you can
stack them vertically interconnecting them(vertically) with each other,
by means of the following anchors:
3.
Previously remove the fiber-pass rubbers to facilitate the approxima-
tion between registers:
5
EN