rcf L-PAD 16CXusb Manual Del Usuario página 7

FUNCTIONS
[6] EQUALIZATION OF CHANNELS 1 TO 8 (L-PAD 16CX USB) / 1 TO 16 (L-PAD 24CX USB).
LOW CUT: if pressed, inserts a high‑pass filter in the respective channel with cut‑off frequency of 75 Hz and 12 dB
/ octave gradient. We recommend that you only insert it when you use voice microphones (or for instruments with
limited low frequency extension), so as to prevent any echoes.
HI: control of the level of high frequencies (12 kHz, –15 ÷ +15 dB).
MID: semi‑parametric control of the level of mid frequencies (–15 ÷ +15 dB), where the frequency of operation is
selectable (100 ÷ 8000 Hz) via the FREQ control.
LOW: control of the level of low frequencies (80 Hz, –15 ÷ +15 dB).
[7] EQUALIZATION OF CHANNELS 9-10 AND 11-12 (L-PAD 16CX USB) / 17-18 AND 19-20
(L-PAD 24CX USB).
LOW CUT: if pressed, inserts a high‑pass filter in the respective channel with cut‑off frequency of 75 Hz and 12 dB
/ octave gradient. We recommend that you only insert it when you use voice microphones (or for instruments with
limited low frequency extension), so as to prevent any echoes.
HI: control of the level of high frequencies (12 kHz, –15 ÷ +15 dB).
HI-MID: control of the level of high‑mid frequencies (3 kHz, –15 ÷ +15 dB).
LO-MID: control of the level of low‑mid frequencies (500 Hz, –15 ÷ +15 dB).
LOW: control of the level of low frequencies (80 Hz, –15 ÷ +15 dB).
[8] EQUALIZATION OF CHANNELS 13-14 AND 15-16 (L-PAD 16CX USB) / 21-22 AND 23-24
(L-PAD 24CX USB).
HI: control of the level of high frequencies (12 kHz, –15 ÷ +15 dB).
HI-MID: control of the level of high‑mid frequencies (3 kHz, –15 ÷ +15 dB).
LO-MID: control of the level of low‑mid frequencies (500 Hz, –15 ÷ +15 dB).
LOW: control of the level of low frequencies (80 Hz, –15 ÷ +15 dB).
[9] CONTROLS OF AUX AND FX EFFECTS LEVELS FOR EACH CHANNEL.
IMPORTANT NOTE
There are two types of auxiliary send level controls:
PRE-FADER (independent from the control of the channel level), to be used for stage monitors;
IMPORTANT
POST-FADER (next and so subject to the control of the channel level), used for the connection, for instance, of signal
processors (effects such as reverb, delay, etc.)..
PRE / POST‑FADER can be selected for AUX 1 and 2 sends, AUX 3 and FX are only POST‑FADER.
The effect control can be used as a fourth auxiliary send (by disabling the internal effect by pressing the FX‑MUTE
key) for connection to an external signal processor.
AUX 1: control of the AUX 1 auxiliary send level – ∞ ÷ +10 dB.
AUX 2: control of the AUX 2 auxiliary send level – ∞ ÷ +10 dB.
PRE / POST: AUX 1 and 2 are PRE‑FADER if this key is released, or POST FADER if pressed.
AUX 3: control of the AUX 3 auxiliary send level – ∞ ÷ +10 dB.
FX: control of the effect level (or fourth auxiliary send; – ∞ ÷ +10 dB).
7