Toyotomi zibro LC-DX320 Instrucciones De Uso página 18

B
FILLING FUEL
ill the removable tank in a suitable place since there can al ays be some
spillage. ollo the procedure belo :
1 Make sure that the heater is switched off.
2 Open the upper lid and lift the removable tank out of the heater ( ig. B).
Put do n the removable tank (cap pointing up ards, handle on floor) and
scre off the fuel cap ( ig. C).
NOTE: Some drops may leak from the tank.
3 ill the removable tank using a fuel pump (refer to fuel pump operation
instructions.) Make sure that it is in a higher position than the removable tank
( ig. D). Insert the ribbed hose into the opening of the removable tank.
4 Check the removable tank fuel gauge
filling once the gauge indicates that the tank is full. Never overfill the tank,
especially not when the fuel is very cold (fuel expands when it heats up).
5 Let the remaining fuel in the pump flow back into the jerrycan and carefully
remove the pump. Carefully screw the fuel cap back on the tank. Clean off
any spilled fuel.
6 Check whether the fuel cap is straight and tightened properly. Reinstall the
removable tank in the heater (cap down). Close the lid.
C
SETTING THE CLOCK
It is only possible to set the correct time, when the heater is connected to the
mains and not burning. Use the adjustment keys
either of the t o keys to s itch on the function (the -digit ¸ will start blinking).
Next, set the hours using the key on the left ( hour) and the minutes using the
key on the right ( min.). Press once to increase the value by one step. When you
hold down the key, the value will continue going up, until you release the key
again. After appro imately 10 seconds the -digit
ting ill be locked ( ig. ). 5 minutes after s itching off the heater, the informa-
tion on the display will disappear and the heater will automatically switch into the
stand-by position.
!
When the heater has been unplugged (or after a power failure), the time needs
to be set again.
D
IGNITING THE HEATER
When used for the first time, a new heater may give out a smell for a short while.
You should therefore provide extra ventilation.
Al ays ignite the heater
cigarette lighter.
Just press the button ¹ to ignite the heater. The POWER lamp
indicating that the ignition procedure has started. This will take a short while.
Once the heater is burning, the POWER lamp
display ¸ will show two numbers. The light next to them indicates that these
numbers refer to the temperatures ( ig.
indicated belo ROOM,
latter can be changed with the adjustment keys (refer to Section E).
Prior to igniting the heater, al ays check for sufficient fuel in the removable tank.
E
SETTING THE REQUIRED TEMPERATURE
The temperature setting can only be adjusted,
the adjustment keys
keys to switch on the function (the °C mark ¸ will start blinking). Next, adjust the
temperature using the key on the right ( min.) to set the temperature to a higher
setting and the key on the left ( hour) to lo er the temperature. Press once to
increase the value one step. After appro imately 10 seconds the C mark
blinking and the setting
The available temperature settings range from
When the heater has been unplugged (or after a power failure), the temperature
will reset to the factory setting of 20°C.
4
6
hile filling the tank ( ig. E). Stop
ith the button ¹. Never use matches or a
ill remain lit (red). The information
). The actual room temperature is
hile the temperature setting is indicated belo
to adjust the temperature. irst press either of the t o
ill be locked ( ig. ).
to set the time. irst press
ill stop blinking and the set-
ill start blinking,
SET. The
hen the heater is burning. Use
C minimum to 28 C ma imum.
empty
F: When the 4-digit
stops blinking, the set-
ting has been locked to
the indicated value.
G: The required tempe-
rature on the left, the
measured temperature
on the right.
ill stop
C
D
E
full