Optional Accessories - Arbortech PCH.FG.600.40 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 38
b. Always wear correct safety clothing, including ear, eye
protective gloves and lung protection.
c. Follow local government safety regulations when
working on materials treated with or containing toxic
substances.
d. Do not use this tool in wet conditions or in the presence
of flammable liquids and gases.
e. Check tool before using. Test run the power tool with no
load prior to use. Do not use damaged tools.
f. Apply lubricant oil the Power Chisel every 15 minutes of
use. As shown in Fig. D, apply lubricant from the Oil
bottle into the oil port.
g. Do no exert excessive pressure. The excessive pressure
will overheat the chisel and the cam leading to
premature failure.
SWITCHING ON AND OFF
This power tool is equipped with lock-on switch. To start the
power tool, push the On/Off Switch (5) forwards (Fig. B) then
press it down at the front until it latches. To switch off the
tool briefly push down the back of the On/Off Switch and
release.
WARNING: The tool includes a restart prevention
feature, which prevents uncontrolled restarting after an
interruption to the power supply. To resume operation,
switch the tool to the off position and start the machine
again.
This power tool has variable speed control. Ensure an
appropriate speed setting is selected for the application
from the table below.
Speed
Application
Setting
5 – 6
Chiselling of wood - general
4 – 5
Medium chiselling of wood like materials for
unique applications
1 – 4
Lighter chiselling of wood like materials for
detailed applications
Support and secure the workpiece to prevent movement
and loss of control. Operate the tool using two hands for
better control. Ensure the tool is running before contacting
the work piece. Approach the workpiece with caution to
avoid sudden hammering and gently push against it. If the
applied pressure is too light, the chisel will not hammer. Hold
the grinder at an angle of 25° as shown in Fig. E. Move the
tool in the desired direction, keeping contact between the
workpiece and the chisel.
WARNING: Do not use the chisels as a lever to break out
wood.
MAINTENANCE
WARNING: Before any adjustment, cleaning or
maintenance work on the machine itself, disconnect from
the power supply.
Inspect the Chisel Arm Base (7) is securely mounted. If loose,
ensure the arm is fully inserted and seated correctly on the
grinder then retighten the Clamping Bolt (6).
Inspect the accessories for damage and maintain them as
specified in their user manual.
For your safety and the reliability of this product, all
electrical repair and maintenance of the internal parts,
other than maintaining accessories and attachments,
should be carried out by Arbortech authorised service
centres.
CHISEL SHARPENING
Remove the chisel from the unit. Use conventional chisel
sharpening methods. Maintain the angle on the cutting
edge. Check the Arbortech website for detailed sharpening
instructions.
CLEANING THE AIR VENTS AND SWITCH
Regularly check to see if any dust or foreign matter has
entered the air vents, or under the On/Off switch. If so, use
a soft brush to remove any accumulated dust to clean the air
vents and switch.
INSPECTION AND WEAR
To inspect the tool for wear, insert a chisel into the chisel
arm. Ensure that the chisel is firmly located and cannot move
within the Chisel Arm. If the chisel has excessive side
movement, internal guides may be worn and should be
replaced by an Arbortech authorised service centre.
If the chiselling impact performance has decreased, inspect
the chisel shaft for excessive wear or replace the chisel. If the
chisel wear is acceptable, an internal cam may be worn and
should be replaced by an Arbortech authorised service
centre.

OPTIONAL ACCESSORIES

To avoid the risk of injuries or damaging your tool, use only
Arbortech recommended accessories and attachments.
Consult your dealer for availability of optional accessories.
POWER CHISEL ACCESSORIES
Spare Parts
PCH.FG.001/2/3/6/11/12/13 - Chisels /various profiles/
PCH.CO.CAM600 - Cam M14 x 1.5 thread pitch with Oil
ENGLISH
PCH.CO.CAM600.20 - Cam 5/8 UNC thread pitch with Oil
PCH.FG.050 - Service Kit
PCH.FG.055 - Oil refill Pack

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Pch.fg.600.6010274748

Tabla de contenido