Enabling Password Protection, Changing Passwords And Defining User Rights; Configuring Alarm Inputs - Monacor IOR-204 Manual De Instrucciones

7.7 Enabling password protection, changing
passwords and defining user rights
According to the factory settings, access to the recorder is not
protected. The predefined password "admin" is not enabled,
i.e. it must not be entered to make any changes to the settings.
When the recorder is connected to a network, always make
sure to enable the password protection feature and to
change the password (also see chapter 3, "Important Data
Security Notes").
1) Show the toolbar to call up the ma in menu: Press the right
mouse button or move the mouse pointer to the centre of
the lower edge of the screen.
2) Click the icon
3) The menu "Parameter" is selected. Click "System" and
there, on the far left, click the submenu "Users".
Parameter Record Search
General
No.
Users
Info
Log
Intelligent Ana
Fig. 7-23 Menu for passwords and user groups
4) Line number 1 for the administrator password is selected.
To change the password and to enable the password pro-
tection feature, click the button "Edit".
User Edit
User Name admin
User Name admin
Password Enable Disable
Password
Confirm
Default Save
Fig. 7-24 Window to change passwords
5) Change the user name "admin", if desired.
6) Set the line "Password Enable" to "Enable": The user lock
will be activated after 2 minutes when no menu is displayed
and the recorder is not operated.
7) In the line "Password", enter a new password with a length
of at least 8 characters. Re-enter the password in the line
"Confirm".
Important: For remote recorder control and remote ac-
cess via the network, the password must consist of exactly
8 characters. It is possible to enter more characters; this
password, however, will be regarded as invalid by the soft-
ware for remote access ("ActiveX").
8) To save the new password, click "Save". When the pass-
word has been successfully saved, a corresponding message
will appear; click "OK" to confirm.
9) To define user rights, first assign a user name and a pass-
word to each user as described above.
10) When a line for a user has been selected, the button "Per-
mission" will additionally appear at the bottom of the
menu. Click the button to define the user rights.
44
Main Menu.
i
Device System Advanced
User Name Level
1 admin ADMIN
2 user1 USER1
3 user2 USER2
4 user3 USER3
5 user4 USER4
6 user5 USER5
7 user6 USER6
Cancel
User Name
Log Search
Disk Manage
Backup
1 2 3 4
Live
1 2 3 4
Playback
1 2 3 4
PTZ
1 2 3 4
Fig. 7-25 Menu for the user rights
Define the rights of the user selected and save them. If
applicable, repeat this procedure for any additional users.
i
11) To save the rights, click "Save".

7.8 Configuring alarm inputs

When alarm sensors such as motion detectors or photoelectric
sensors are connected to the contacts SENSOR
Shutdown
1 – 16 (17), configure the alarm inputs by means of the menu
2
Enable
Enable
"Parameter", submenu "Alarm", section "Alarm".
Disable
Disable
Disable
Disable
Parameter Record Search
Disable
Display
Disable
Record
Capture
Network
Edit Cancel
Alarm
Motion
Alarm
PTZ Linkage
Fig. 7-26 Menu for the alarm inputs
Menu item
Alarm In
Alarm Type
Latch Time
Buzzer
Post Recordung
Alarm Out
Show Message
Send Email
Full Screen
Copy
Default
Save
Cancel
Lettering for the models IOR-204 and IOR-208
1
Lettering for the model IOR-232POE
2
User Permission
user1
Parameter Maintain
Remote Login SEQ Control
All Clear Save Cancel
i
Device System
Alarm In IO-1
Alarm Type Normally-Open
Latch Time 10 s
Buzzer OFF
Post Recording 30 s
Alarm Out
Show Message Send Email Full Screen
Record Channel
1 2 3 4
Copy IO-1 To All
Function
To select the alarm input
To select the contact type
Normally-Open
Normally-Close
OFF = input signal will not be evaluated
Time the icon I will appear in the live image
and time the camera image will be displayed in
full-screen mode
Duration of the alarm sound:
OFF, 10 s, 20 s, 40 s, 60 s
Duration of an alarm-triggered recording
The alarm will be routed to the output ALARM
or OUT (17)
2
In the live image, an alarm will be indicated
I
by the icon
In case of an alarm, an e-mail will be sent;
for the e-mail settings, refer to menu "Parameter",
submenu "Network", section "Email"
The corresponding channel will be displayed in the
full-screen mode
To use the settings of an alarm input
for additional inputs
Reset to factory settings
To save the setting
To exit the menu
Manuel Record
Manual Capture
(12) or ALARM
1
Advance Shutdown
Copy
Default Save Cancel
(12)
1