FALMEC Virgola Evo Manual De Instrucciones página 18

OPERATION
WHEN TO TURN ON THE HOOD?
Switch on the hood at least one minute before starting to cook to direct
fumes and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all
vapours and odours. By means of the Timer function, it is possible to set
auto switch-off function which will allow the hood to turn off automat-
ically after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
1st speed: maintains the circulation of clean air with low electricity
consumption.
2nd speed: normal conditions of use.
3rd speed: presence of strong odours and vapours.
4th speed: rapid disposal of odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The metal filters must be cleaned every 30 hours of operation.
The HP active carbon filters (optional), must be reactivated every 3-4
months, depending on the use of the hood.
For further details see the "MAINTENANCE" chap.
ELECTRONIC PUSHBUTTON PANEL
Motor ON/OFF
Upon start-up, the speed is that stored at the previous op-
eration.
Increase speed from 1 to 4
Speed 4 is only active for a
few minutes, then speed 3
activates.
Reduce speed from 4 to 1
Light on/off
Short impulse: turn light on and off
Long impulse: change light tone from 2700K to 5600K
TIMER (red LED flashing)
Auto switch-off after 15 min.
The function deactivates (red LED off ) if:
- The TIMER key ( ) is pressed again.
- The ON/OFF key ( ) is pressed.
USING THE RADIO CONTROL (OPTIONAL)
WARNINGS!:
Place the hood away from sources of electromagnetic
waves (e.g. microwave ovens), which could interfere with
the radio control and with the hood electronics.
The maximum operating distance is 5 metres, that may vary ac-
cording to the presence of electromagnetic interferences.
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the figure.
The speeds are indicated by
the LEDs on the keys:
Speed 1
Speed 2
Speed 3
Speed 4
("+" LED flashing)
ACTIVATION PROCEDURE
Before using the radio control, follow the procedure below on the
hood pushbutton panel:
• Press LIGHT ( ) and TIMER (
flashing.
• Release the two keys and press LIGHT (
up.
• Release LIGHT ( ): now the receiver is active.
This procedure is also used to deactivate the receiver.
RADIO CONTROL CODE CHANGE
With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be creat-
ed by following the procedure below.
Disconnect the power to the hood before starting the pro-
cedure.
1) - CREATE A NEW CODE
The procedure is to be carried out on the radio control.
• Press LIGHT
and TIMER
flashing.
• Press DOWN
on the radio control: saving is confirmed by three
brief flashes of the display. The new code cancels and replaces the
previous default code.
Reconnect the hood to the electrical power supply, making
sure that the lights and motor are off.
2) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
USING THE ELECTRONIC PUSHBUTTON PANEL
) on the hood pushbutton panel for 2 seconds:
press TIMER (
the red LED lights up.
press any key on the radio control within 10 seconds.
RESTORING DEFAULT CODE
the procedure is to be carried out if the hood is disposed of, sold or
transferred.
Disconnect the power to the hood before starting the pro-
cedure.
• Press UP
and DOWN
more than 5 seconds: reset is confirmed by three brief flashes of the
display.
• Reconnect the hood to the electrical power supply.
• Proceed with associating the hood and the radio control, as de-
scribed in point 2.
18
DESCRIPTION OF TRANSMITTING
COMMANDS
UP
Motor switch-on and speed in-
crease from 1 to 4. Speed 4 is only
active for a few minutes.
DOWN
Speed decrease and
switch-off.
Light ON-OFF
Short impulse:
turn light on and off
Long impulse:
change light tone from 2700K to
5600K
TIMER ON: The motor automati-
cally switches off after 15 min.
The function is automatically dis-
abled if the motor is switched off
( key)
Command transmission active
) simultaneously until all LEDs start
) again until all LEDs are lit
simultaneously until the display starts
simultaneously on the radio control for
motor