Intimus H200 CP4 Instrucciones De Uso página 6

GB
OPERATING FUNCTIONS (Figs. 1, 2 and 4):
1 = Mains switch (Emergency-stop) (fig. 1)
This switch turns the machine either on (po-
sition „1") or off (position „0").
2 = „Cutting system forward"
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
Note: Press and hold button for approx. 1
sec.
3 = „Cutting system stop"
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse"
pushbutton (fig. 2)
Pressing this button starts the cutting system
in reverse.
Note: Press and hold button for approx. 1 sec.
5 = Pilot lamp (fig. 2)
a) „ready"
Continously lights when the mains switch
(1) is operated.
b) „motor protection"
Flashes when the motor is overloaded.
The machine cannot be started during the
cooling down phase of the motor. Additional
the pilot lamp of the control display (7)
(fig. 2) lights up.
6 = Pilot lamp „paper jam" (fig. 2)
Lights when too much paper is fed to the
cutters (see description „AUTOMATIC RE-
SPONSE IN CASE OF OVER-LOADING").
7 = Pilot lamp (fig. 2)
a) „door open"/„hopper open"
Lights when the door is not closed or when
the hopper is open. The machine then
switches off automatically and it cannot
be started as long as the door is open or
the hopper is open.
Note: To turn the machine into the „Rea-
dy"- mode again after an interruption, there
must be operated both end switches at
the corresponding turn-off device. For this
the door must be openend before not less
than 10 cm or the hopper must be folded
upwards with a minimum of 10 cm.
I
MAINS SWITCH
Fig. 1
b) „collecting bag full" (fig. 2)
Lights as soon as the collecting bag is full
and needs to be emptied. At the same time
the machine switches off automatically.
8 = Light barrier (forward operation) (fig. 5)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
OPERATING THE MACHINE:
To start, switch on the unit by operating the mains
switch (1) (fig. 1). The pilot lamp marked „ready
for operation" (5), as well as the red stop-button
„S" (3) (fig. 2) will light to indicate that the machine
is ready for operation.
The paper tray may not be used as
a step ladder or as a seat. Danger of
tipping over!
FEEDING CRUMPLED PAPER:
(Model 852CC)
1. Fill the hopper with crumpled paper.
Note: The crumpled paper can be dropped
directly from the wastepaper basket into the
hopper of the machine. The apportioning wings
preceding the cutting mechanism ensure more
or less uniform distribution of the paper.
Attention: The wastepaper basket is no refuse
tin and should not be emptied into the machine
thoughtlessly - in no way can the machine
destroy bottles, pens, pencil sharpeners etc.
2. Press the pushbutton switch „forward" (2) (fig. 2).
The cutting system runs and begins to shred
the paper.
Note: Do not feed any smooth paper until the
crumpled paper is completely shredded.
3. To switch the machine off press the red stop-
button (3) (fig. 2).
FEEDING SMOOTH PAPER:
- Feed smooth paper through the opening at the
lower part of the hopper (model 852CC) or th-
rough the opening of the hopper (model 802CC)
to the cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
S
1 4 3
Translation of the Original Operation Manual
Übersetzung der Originalbetriebsanleitung
OPERATION
2 5 6 7
Fig. 2
6
Never feed the shredder with a quantity
of paper exceeding the maximum indi-
cated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC RE­
SPONSE IN CASE OF OVERLOADING".
AUTOMATIC RESPONSE
IN CASE oF „ovERLoADING":
In case you accidentally overload the shredder,
it will automatically alleviate the problem as
follows:
1. The cutting system becomes jammed. The pilot
lamp (6) (fig. 2) lights up.
2. The cutting system runs briefly in reverse,
thereby freeing the material to be shredded.
3. The cutting system automatically switches back
to forward mode.
The machine repeats this process until all the
material has been shredded satisfactorily.
EMPTYING THE COLLECTING BAG (Fig. 4):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (7) (fig. 2) lights
up. Empty the collecting bag as follows:
- Open the door and take out the sliding frame
with the collecting bag.
- Remove the rubber band, take out the full bag
and dispose of contents.
- Put the empty bag from below through the sliding
frame and put the edges of the bag approx.
10 cm over the frame outwardly.
- Fix the collecting bag with the rubber band at
the sliding frame.
- Move back the sliding frame with the collecting
bag and close door.
Note: The machine will only run with closed
door!
Fig. 4