Tips for Success
CORRECT
1. Make sure fi nger is clean and dry.
Place fi nger fl at above the sensor strip
with the top knuckle above the sensor.
2. Swipe fi nger straight down keeping
fi rm contact with the sensor. The swipe
should be a slow, constant speed.
SPECIAL NOTES: Use the same fi nger
for every swipe. It is important to swipe
fi nger slowly and fi rmly as this is the reason most swipes fail.
Swipe finger straight down
keeping firm contact with
the sensor.
Start swipe with
the top knuckle
above the
sensor strip.
Sensor Strip
INCORRECT
• Do not bend fi nger during swipe as this will only scan the tip of
your fi nger.
• Swipe fi nger straight down, not at an angle.
• Swipe fl at, not tilted or rolled to one side.
Cover
Resend button: When
pressed the door will stop if
moving up or reverse if
moving down.
Send LED (yellow): Lit
after a passed fingerprint
scan and indicates that the
Resend button is active
and can be used to stop
or reverse door travel.
Pass LED (green): Lit when
a scanned fingerprint
matches a stored print.
Ready LED (green): Lit
when unit is ready to scan
fingerprint.
Extra directions are located
on the inside of cover.
Sensor Strip
The scan
should end
at the tip of
finger.
Enroll button: When
pressed the unit will go
into Enroll mode.
Enroll LED (yellow):
Lit when the unit is in
Enroll mode.
ENROLL
Fail LED (red): Lit when
a scanned fingerprint
SEND
ENROLL
does not match a
PASS
FAIL
stored print.
READY
RETRY
Retry LED (yellow): Lit
when another swipe is
Sensor Strip
required.
Step 3 Enroll Initial User
NOTE: The unit requires 3 passed swipes to enroll a user.
1. Open cover to turn unit on. Wait until Enroll
LED and Ready LED are lit (not fl ashing).
2. Swipe fi nger slowly and fi rmly down the
sensor strip until three passed swipes are
made.
NOTE: The Pass LED will light for a passed
swipe. The Retry LED will light if another swipe
is needed. Swipe slowly and with more pressure
if this occurs.
3. After the third passed swipe, the Enroll and
Pass LED will fl ash. Enrollment is complete.
NOTE: If cover is already open, press either
the Resend or the Enroll button to turn unit on.
If the Ready LED is lit refer to Factory Reset in
the Erase/Reset section.
Step 4 Enroll Additional User(s)
NOTE: The device can store up to ten fi ngerprints at a time. An
enrolled user must swipe fi nger fi rst to enroll new user.
1. Open cover and wait until Ready LED
is lit.
2. Press and hold Enroll button until Enroll
LED starts to fl ash.
3. While the Enroll LED is fl ashing an
enrolled user must slowly and fi rmly
swipe fi nger.
4. The Enroll LED and Ready LED will light
when ready for new user to swipe fi nger.
5. New user should swipe fi nger slowly and
fi rmly down the sensor strip until three
passed swipes are made.
6. The Enroll LED and Pass LED will fl ash
when new user is enrolled. Unit will return
to Ready mode.
NOTE: If cover is already open, press either the Resend or the
Enroll button to turn unit on. The Pass LED will light for a passed
swipe. The Retry LED will light if another swipe is needed.
2
1
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
2
3
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
1
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
2
3
4
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY
5
6
ENROLL
SEND
ENROLL
PASS
FAIL
READY
RETRY