Intended Use; Noise/Vibration Information; For Your Safety - stayer RO125 Manual De Instrucciones

This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates of
our machines on the website: www.grupostayer.com
1_PRODUCT SPECIFICATION
Eccentric Sander
Voltage V
Rated input power W
No-load speed min 4000-13000
-1
Ø Oscillation
mm
excursion
Ø Sanding plate mm
Weight Kg
Protection class
The specifications apply for the rated voltage of [U] 230/240
V ~ 50/60 Hz. - 110/120 V. ~ 60 Hz. For lower voltages and
with models for specific countries, the specifications can
vary.
Please refer to the article number on the nameplate of
your machine since the trade designation of individual
machines can vary.
2. PRODUCT ELEMENTS
The numbering of the machine elements refers to the
illustration of the machine on the graphic page.
1 Speed selector thumbwheel
2 On/off switch
3 Vacuuming adapter
4 Auxiliary Handle
5 Sanding sheet
6 Lock button
7 Sanding plate

3. NOISE/VIBRATION INFORMATION

Measured values determined according to EN 60745.
Typically, the A-weighted sound pressure level of the
product is 81 dB(A).
Measuring inaccuracy K = 3 dB.
The noise level when working can exceed 85 dB(A).
Wear ear protection!
The typical hand-arm vibration is below 2.5 m/s2
in both models.
The vibration emission level given in this information sheet
has been measured in accordance with a standardized
test given in EN 60745 and may be used to compare one
tool with another.
The vibration emission level will vary because of the ways
in which a power tool can be used and may increase
above the level given in this information sheet.
This could lead to a significant underestimate of exposure
when the tool is used regularly in such a way.
RO150E LOM L20 RO125
230 Ac 18 dc 230 Ac
450 300
5000-9000 4000-12000
2.5 2
150 125
2.4 1.5*
/ ll / ll
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when the
tool is switched off and when it is running but not actually
doing the job. This may significantly reduce the exposure
level over the total working period.

4. INTENDED USE

The machine is intended for dry sanding of wood.
Machines with electronic control are also suitable for
300
polishing.

5. FOR YOUR SAFETY

2
125
Read all instructions Failure to follow all instructions lis-
1.4
ted below may result in electric shock, fire and/or serious
/ ll injury.
SAVE THESE INSTRUCTIONS.
In addition, the general safety instructions either
enclosed or included in the middle of these opera-
ting instructions must be observed.
Hold the machine firmly with both hands while wor-
king and provide for secure footing. The machine is
more securely guided with both hands.
Secure the work piece. A work piece clamped with
clamping devices or in a vice is held more securely than
by hand.
Do not work with materials containing asbestos. As-
bestos is considered carcinogenic.
Take protective measures when dust can develop du-
ring working that is harmful to one's health, combus-
tible or explosive. Example: Some dusts are regarded as
carcinogenic. Wear a dust mask and work with dust/chip
extraction when connectable.
Keep your workplace clean. Material mixtures are es-
pecially dangerous. Light metal dust can burn or ex-
plode.
Do not use the machine with a damaged cable. If the
cable is damaged while working, do not touch the da-
maged cable but pull the mains plug. A damaged ca-
ble increases the risk of an electrical shock.
For machines used outdoors, connect to the mains
using a fault current (FI) protection switch.
Use the electro-tool only for dry sanding. The penetra-
tion of water into the electro-tool increases the risk of an
electrical shock.
Take care that no persons are endangered by flying
sparks. Remove combustible material from the vicini-
ty. When sanding metals, sparks are produced.
Caution, fire hazard! Avoid overheating of the sanded
material and the electro-tool. Always empty the dust
container before pauses in the work. For unfavoura-
ble conditions such as flying sparks when sanding metals,
- 9 -
es
it
gb
de
fr
p
pl
cz