SIOUX C Serie Instrucciones Y Lista De Piezas página 3

STANDARD REVERSE OPERATION
The spindle rotation is controlled by the slide on the top, rear of the tool. To ensure maximum performance, make sure the slide is in the full left or right position.
Move the slide fully to the right for right hand (clockwise) rotation of the chuck.
Move the slide fully to the left for left hand (counterclockwise) rotation of the chuck.
RAPID REVERSE OPERATION
The spindle rotation is controlled by the button on the top, rear of the tool Press, and hold, the button to operate the tool in reverse spindle rotation. Release
the button to operate the tool in forward rotation (right hand). To ensure maximum performance, make sure the button is fully pressed, or fully released.
AIR SUPPLY
The efficiency and life of this tool depend on the proper supply of clean, dry air at a maximum of 90 PSI. The use of an air line filter, pressure regulator,
and lubricator is recommended. Before connecting to tools, blow out the air line to remove water and dirt that may have accumulated.
HOSE AND HOSE CONNECTIONS
The air supply hose recommended is 3/8" (10mm) I.D. If an extension hose is necessary, use 1/2" (13mm) ID hose with couplings not less than 3/8" (10mm) I.D.
LUBRICATION
For maximum performance and tool life, an air line lubricator, set to deliver 2 drops per minute, is recommended. SIOUX No. 288 Air Motor Oil is recommended.
If an airline lubrication is not used, it is recommended that the tool be oiled daily before use to improve performance. Add 2-4 drops of air motor oil and run the
tool for 10-20 seconds to distribute oil through the tool. Lubricate the gears through the grease fitting with Sioux 1232A grease after 100 hours of operation.
MAINTENANCE
Water, dust and other airline contaminants can cause rust and vane sticking. For long periods between tool use, flush the tool with a few drops of oil
and run for 10 seconds. This will help remove contaminants and reduce the formation of rust. Check the speed of the tool regularly by placing a contact
type tachometer to the chuck. In addition, always check the speed and do a simple vibration check after any servicing. If the tool exceeds the rated
speed or vibrates excessively discontinue use and contact an Authorized Sioux Service Center.
Speed
Catalog No.
(RPM)
SDR6P3N2 300
SDR6P4N3 400
SDR6P4N4 400
SDR6P7N3 700
SDR6P7N4 700
SDR6P12N3 1200
SDR6P16N3 1600
SDR6P26N2 2600
SDR6P26N3 2600
SDR6P26N4 2600
SDR6P40N2 4000
SDR6P40N3 4000
SDR6P60N2 6000
SDR6P60N3 6000
SDR6P3RLFRR 300
SDR6P3R3RR 300
SDR6P3R4RR 300
SDR6P5R3RR 500
SDR6P5R4RR 500
SDR6P7R3RR 700
SDR6P7R4RR 700
SDR6P7RK4RR 700
SDR6P12R3RR 1200
SDR6P12R4RR 1200
SDR6P20R2RR 2000
SDR6P20R3RR 2000
SDR6P20RK3RR 2000
SDR6P20R4RR 2000
SDR6P20RK4RR 2000
SDR6P25R2RR 2500
SDR6P25R3RR 2500
SDR6P25RK3RR 2500
SDR6P25R4RR 2500
SDR6P25RK4RR 2500
SDR6P40R2RR 4000
SDR6P40R3RR 4000
SDR6P40RK3RR 4000
Form ZCE772B
Disconnect tool from air supply before installing or removing drill bit or making any adjustments
NOISE AND VIBRATION READINGS
Weight Chuck Capacity
lbs. kg. in.
2.7 1.2 1/4
2.7 1.2 3/8
3.1 1.4 1/2
2.7 1.2 3/8
3.1 1.4 1/2
2.7 1.2 3/8
2.7 1.2 3/8
2.1 0.9 1/4
2.3 1.0 3/8
2.7 1.2 1/2
2.1 0.9 1/4
2.3 1.0 3/8
2.1 0.9 1/4
2.3 1.0 3/8
2.9 1.3 3/8
3.1 1.4 1/2
2.9 1.3 3/8
3.1 1.4 1/2
2.9 1.3 3/8
3.3 1.5 1/2
3.1 1.4 1/2
2.9 1.3 3/8
3.3 1.5 1/2
2.1 0.9 1/4
2.3 1.0 3/8
2.4 1.1 3/8
2.7 1.2 1/2
2.5 1.1 1/2
2.3 1.0 1/4
2.5 1.1 3/8
2.3 1.0 3/8
2.9 1.3 1/2
2.7 1.2 1/2
2.3 1.0 1/4
2.5 1.1 3/8
2.3 1.0 3/8
WARNING
Noise (Tested in accordance with ISO
Standard 15744)
Sound Sound Power
mm.
Pressure (dBA) (dBA)
0.6 HP Non-reversible
6 TBD TBD
10 TBD TBD
13 TBD TBD
10 TBD TBD
13 TBD TBD
10 TBD TBD
10 TBD TBD
6 TBD TBD
10 TBD TBD
13 TBD TBD
6 TBD TBD
10 TBD TBD
6 TBD TBD
10 TBD TBD
0.6 HP Rapid Reversing
Contact Sioux Tools if needed
10 TBD TBD
13 TBD TBD
10 TBD TBD
13 TBD TBD
10 TBD TBD
13 TBD TBD
13 TBD TBD
10 TBD TBD
13 TBD TBD
6 TBD TBD
10 TBD TBD
10 TBD TBD
13 TBD TBD
13 TBD TBD
6 TBD TBD
10 TBD TBD
10 TBD TBD
13 TBD TBD
13 TBD TBD
6 TBD TBD
10 TBD TBD
10 TBD TBD
3
Vibration (Tested in
accordance with ISO
Standard 28927-5:2009)
Uncertainty Vibration
Uncertainty, K (m/s
(dBA) (m/s )
2
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
3.0 TBD TBD
Date
)
2
2018July5/J