Ferlux ZEUS Instrucciones De Instalación, Uso Y Mantenimiento página 15

Do not use the appliance if the glass is broken.
Do not use flammable liquids, fats or any unsuitable fuel.
CREOSOTE REMOVAL – HOW IT FORMS AND HOW TO CLEAN IT
When wood burns slowly it gives off organic vapours and tar-like by-products that react with the steam released by the wood and create a build-up of creosote
on the walls of a relatively cold chimney.
If these build-ups burn or catch fire they can cause an extremely hot fire.
Creosote build-up should be checked daily until you are familiar with the fireplace as used in your case and can tell how frequently it needs to be cleaned.
Remember that the greater the combustion the less creosote builds up, so it may be necessary to clean the appliance every week in mild weather but only
every two months during very cold spells. The chimney should be inspected every two months to check the creosote build-up over that time and, if necessary,
remove it.
To avoid daily creosote formation and prevent build-ups, we recommend a hot fire from time to time with the fireplace door closed.
Only use suitable equipment for cleaning your chimney and ensure that others do likewise.
Sweep the chimney twice a year.
GENERAL INFORMATION
Consult your local authority building inspector, fire brigade or insurance agent to find out what regulations are applicable in your area. They will also be able to
inform you about inspections of your installation. The maintenance of models must be done by qualified person.
Read these instructions carefully before installing the appliance. Mistakes can cause damage to people and property.
Keep these instructions.
I. - FUEL AND ADDING MORE FUEL
To obtain efficient working of the fireplace, use only wood that has been dried for a minimum of 2 years. It is advisable to use dried firewood from beech, holm
oak, olive tree or any other with similar caloric features. Hardwoods are preferred to softwoods such as poplar, willow, aspen, etc.
Only use dry wood with less than 20% humidity. Green wood produces less heat and more creosote. Green wood and wet wood also suffocate the fire and lead
to abnormal creosote build-up, which can cause chimney fires.
Solid mineral fuels such as coal etc. must not be used. Neither must tropical woods such as mahogany, framire, okabe, etc. The use of chemicals or liquids
such as oil, alcohol, fuel oil, naphthalene, etc. as fuels or fire-lighters is also forbidden.
Do not use the appliance as an incinerator.
When adding more fuel, make sure that the ashtray is enough empty to let the natural air going through and not destroy the grill/base.
When inserting firewood, handle the door gently.
Normal load of wood: approximately 3 or 4 logs, 12 to 15 cm (4 ¾" - 6") in diameter.
Before loading for a slow fire, allow the flames to die down; do not load on top of embers that are too bright.
II.- TO LIGHT THE FIRE
1.- Empty the ashtray.
2.- Put the wood into the firebox.
3.- Light the fire using kindling (small sticks of wood) or firelighters.
4.- FIRE up the wood.
5.- Let the door slightly open to avoid dirtying the glass (the glass is relatively cool and resulting condensation can cause soot particles to stick to the glass).
6.- When the glass is sufficiently hot, close the door. The model always must work with the door closed.
7.- Wait until the kindling is burning well and then add progressively larger pieces of wood.
8.- Follow the instructions below on regulating the fire.
III.- REGULATION OF THE FIRE
The fire is controlled by a primary air regulator which is situated in the centre of the front panel (see diagram). This regulator controls the maximum and
minimum flow of air to the fire. Inserts in cast iron are also provided with a secondary air regulator.
In order to control the fire and avoid the escape of smoke, it is essential to keep the combustion chamber closed. Only open the chamber to add more wood.
Remember that the fire and its exterior will be very hot during the combustion process. Do not touch any surfaces close to it.
INSTRUCTIONS FOR USE
ENG
15