Operating Position - Poulan Pro PPB150E Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Coupler P rimary
Hole
' Guide Recess
Upper Locking/ Attachment
Shaft Release
Button
,tA
rmWARNING:
Make
sure the locking/
release
button
is locked
in the primary
hole
and the knob is securely
tightened
before op-
erating the unit. All attachments
are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment
instruction
manual. Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Secondary
Hole
Locking/Release
Button in Primary
Hole
OPERATING
INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING
POSITION
ALWAYS WEAR:
_,J._(
} Eye Protection
Long Pant
Out from your right to your_lelt.
A
WAR NIN G: Alwayswear
eye
protec-
tion.
Never
lean
over
the
trimmer
head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness
or other
serious
injury.
Do not run the engine at a higher speed than
necessary.
The cutting
line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds,
there
is less engine noise
and vibration.
The cutting
line will last longer
and will be less likely to "weld" onto the spool.
Always
release
the throttle
trigger and allow
the engine to return to idle speed
when not
cutting.
To stop engine:
• Release
the throttle trigger.
• Move the ON/OFF
switch to the OFF posi-
tion.
TRIMMER
LINE
ADVANCE
Thetrimmer
line will advance
approximately
2
inches
(5 cm) each time the bottom
of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient
line length is the maximum
length allowed
by the line limiter.
Always
keep the shield in place when the tool
is being operated.
To advance
line:
• Operate
the engine at full throttle.
• Hotd the trimmer
head parallel to and above
the grassy
area.
• Tap the bottom of the trimmer head lightly on
the ground one time. Approximately
2 inches
(5 cm) of line will be advanced with each tap.
Always
tap the trimmer
head on a grassy
area. Tapping
on surfaces
such as concrete
or asphalt
can cause excessive
wear to the
trimmer
head.
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient
line length.
_, WARNING:
Use only 0,080"
(2 mm)
diameter
line. Other sizes of line will not ad-
vance properly
and can cause serious injury.
Do not use other
materials
such
as wire,
string,
rope,
etc. Wire
can break off during
cutting and become a dangerous
missile that
can cause serious
injury.
CUTTING
METHODS
_WARNING:
Use
minimum
speed
and do not crowd the line when cutting around
hard objects (rock, graveI, fence posts, etc.).
which can damage the trimmer head, become
entangled
in the line, or be thrown
causing
a
serious
hazard.
• The tip of the line does the cutting.
You will
achieve
the
best
performance
and
minimum
line wear by not crowding
the line
into the cutting area. The right and wrong
ways are shown below.
Tip of the Line
Line Crowded
Into
I
Does The Cutting
I
Work Area
Right
_._'_'
• The
line will
easily
remove
grass
and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
• For trimming or scalping,
use tess than full
throttle to increase line life and decrease head
wear, especially:
• During light duty cutting.
• Near objects
around
which tt_e line can
wrap such as small posts, trees or fence
wire.
10

Publicidad

Tabla de contenido
loading

Tabla de contenido