Wall Mounting - Tecomec Jolly Star Manual De Instrucciones

11. UNPACKING
The grinder is supplied already partially assembled.
12. STANDARD SUPPLY (FIG.2)
1 - Base unit
2 - Arm-motor unit
3 - Owner's manual
4 - Test card
5 - Shield guard
Grinding wheel Ø 5 3/4"x1/8"x7/8"
6 -
(145x3.2x22.2 mm)
Grinding wheel Ø 5 3/4"x3/16"x7/8"
7 -
(145x4.7x22.2 mm)
Grinding wheel Ø 5 3/4"x1/4"x7/8"
8 -
(145x6x22.2 mm)
9 - Extra shield guard
10 -Guard securing screw M5x12
13. TESTING THE GRINDING WHEEL
Hold the grinding wheel up by its central hole. Knock the edge of the grinding wheel
(fig.3) gently with a non-metal object. If it makes a numb non-metallic noise it means
that the wheel could be damaged: do NOT use it!
14. INSTALLATION
ATTENTION
Do not install the machine at eye level. You are recommended to install it at a height
of no more than 3.9 to 4.2 feet (1.2-1.3 m) from the floor.
The machine can be bench mounted or wall mounted.
14.1 BENCH MOUNTING
- Securing the base unit (fig.4): use 2 M8 screws complete with washers and nuts
(material not supplied), inserted in the securing holes F4. Make sure you position
the base unit on the bench as illustrated in the detail.
- Fitting the arm (fig.5): to secure the arm-motor unit to the base unit, insert the V5
screw in the dedicated hole F5. Insert the R5 washer at the back and tighten the
knob M5.

14.2 WALL MOUNTING

- Securing the base unit (fig.6): use two dowels with relative screws complete with
washers (material not supplied), inserted in the securing holes F6.
- Fitting the arm (fig.5): to secure the arm-motor unit to the base unit, insert the V5
screw in the dedicated hole F5. Insert the R5 washer at the back and tighten the
nut D5.
14.3 SECURING THE OPERATING HANDLE (FIG.7)
- Insert the screw V7 in the relative hole in the arm and secure it with the nut D7.
- Completely screw the operating handle I7 on the screw V7.
14.4 SECURING THE SHIELD GUARDS
Do not screw the screws too tight during this job to avoid cracking the guards.
- Remove the screw V8 and the flange F8 on the hub (fig.8).
- Secure the guard P9, by screwing the screw V9, complete with washer R9, in the
relative hole F9 (fig.9).
- Secure the arbor shield P10, by screwing the screw V10, complete with washer
R10, in the relative securing hole F10 (fig.10).
15. CHAIN INFORMATION
The chain must be completely inspected before sharpening it to make sure it is intact.
(fig.11) Cutter parts:
1 Top part
2 Top cutting angle
3 Side cutting angle
4 Sharpening recess
5 Depth gauge
6 Bit
7 Heel
8 Rivet hole
16. CHAIN IDENTIFICATION
- Before you start to sharpen, you need to know the type of chain and the relative
adjustment angles. These characteristics are written in the owner's manual of the
chain saw on which the chain is fitted or on the chain pack.
- The chain identification code is usually written on the driving link.
- You can also identify the chain using a template or gauge.
- Consult the CHAIN CHART at the end of this manual.
The columns in this chart provide the following information:
11 - Washers for screws M5
12 - Arm securing screw M10x40
13 - Washer for screw M10
14 - Arm blocking handle
15 - Arm securing nut M10
16 - Operating handle
17 - Operating handle securing screw M6x25
18 - Operating handle securing nut M6
19 - Sharpening template
20 - Dressing brick
21 - 4 mm Allen wrench
22 - 5 mm Allen wrench
(fig.12) Chain parts:
1 Connection link
2 Left cutter
3 Right cutter
4 Driving link (pulling link)
5 Rivet
EN
÷ 2
A
Chain pitch
B Gauge
C
Top sharpening angle (vise rotation)
D Cutting angle (arm rotation)
E Down angle (vise inclination)
F
Gauge depth
G Grinding wheel thickness
H Grinding wheel code
I Oregon chain codes
L Windsor chain codes
M SARP chain codes
16.1 INSTRUMENTAL MEASUREMENTS (FIG.13)
a - Measure the gauge depth using the suitable shape.
b - Put the template on this side and measure the chain PITCH.
c - Put the template on this side to measure the cutter length.
d - The driving link width is measured using a suitable instrument (i.e. gauge).
17. GRINDING WHEEL WARNINGS
- Use a grinding wheel suitable for the type of chain to be sharpened; consult the
chain chart at the end of the manual.
- Do not force the grinding wheel on the hub and do not alter the centering hole
diameter. Do not use grinding wheels that do not fit perfectly in place.
- Use exclusively clean and perfect intact hub and flange to fit the grinding wheel.
- Make sure the outside diameters of the hub and flange are identical.
18. FITTING THE GRINDING WHEEL
- Loosen the screw V10 and turn the guard P10 (fig.14).
- Choose the grinding wheel based on the type of chain to be sharpened (column H
in chain chart).
- Insert and perfectly center the grinding wheel in the dedicated seat on the hub
(fig.14-15).
- Insert the flange F8 and tighten the screw V8 (fig.14).
Make sure you fit the flange as illustrated in fig.15-16.
If the grinding wheel is fitted with the flanges too tight, it could break during
use and put the operator at risk. To avoid such risk, tighten screw M6x25 to
62 in-lbs (7 Nm). If possible, check with dynamometric spanner.
- Close the guard again P10 and tighten the relative screw V10.
19. CHECKING THE ASSEMBLY OF THE GRINDING WHEEL
- Stand at the side of the grinding wheel, start the grinder and visually make sure
the grinding wheel does not oscillate sideways or crosswise, consequently causing
abnormal vibrations.
- If this should be the case, stop the machine immediately and check if the grinding
wheel has been fitted correctly. If necessary, replace the grinding wheel with another
original one.
Always check a freshly fitted grinding wheel at working speed for at least one
minute before you start grinding, standing at a safe distance and making sure
nobody else approaches the machine.
20. ELECTRICAL CONNECTION
- Make sure the electrical system power supply complies with the values written on
the rating nameplate.
- The power supply voltage must not differ from that written on the nameplate by
±5%.
- The connection to the electric mains must be prepared subject to current standards
in force in the country in which the machine is used.
- The power socket used for the machine must have an earth wire, adequate fuse
and must be protected by a differential circuit breaker with tripping sensitivity no
higher than 30 mA.
N Carlton chain codes
O Stihl chain codes
P EM chain codes
3