Before Starting The Equipment - EINHELL TC-MG 220/1E Manual De Instrucciones

The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect con-
ditions.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the plug-in tools (Figures 1/2)
•
To fit the plug-in tools safely you should hold
the multifunction tool so that the ON/OFF
switch (1) points down and the tool mounting
(2) faces up.
•
Place the plug-in tool (e.g. the triangular san-
ding/grinding plant) on the tool mounting (2)
so that the pins of the tool mounting (2) fit into
the recesses in the plug-in tool.
•
Secure the plug-in tool using the supplied
Anl_SA_TC_MG_220_1_E_SPK8.indb 27 Anl_SA_TC_MG_220_1_E_SPK8.indb 27
GB
screw (5) and tighten the screw securely with
the Hexagon key (11).
•
Make sure that the washer (4) is used for the
screw (5) only in connection with the saw bla-
de and the scraper (see Figure 2).
The camber on the washer must face upwards.
Check that the plug-in tool is secure.
5.2 Triangular sanding/grinding plate
Fit the triangular sanding/grinding plate to use the
equipment as a delta sander/grinder.
5.2.1 Fastening the sanding/grinding paper
The Velcro fastener enables easy changing of
sanding/grinding paper. Make sure that the va-
cuum extraction holes on the sanding/grinding
paper and the sanding/grinding disk are aligned.
5.3 Fitting the dust extraction device for the
grinding/sanding plate (Fig. 3/4)
The dust extraction system prevents the accumu-
lation of dirt and high dust loads in the air, and it
makes it easier to dispose of the dust.
•
Place the equipment in a stable position as
shown in 5.1.
•
Fit the dust extraction device (6) with the tool
mounting (2) positioned as shown in Figure 3.
•
Secure the dust extraction device (6) by tigh-
tening the screw (7) with the Hexagon key
(11).
•
Make sure that the washer (4) is used for the
screw (5) (see Figure 2). The camber on the
washer must face upwards.
•
Place the triangular grinding/sanding plate
on the dust extraction device (6) and the
tool mounting (2) so that the pins of the tool
mounting (2) fit into the recesses of the trian-
gular grinding/sanding plate (8), then fasten
as shown in Fig. 4.
•
Connect your tool to an extraction unit or va-
cuum cleaner. This will provide excellent ext-
raction of chips and dust from the workpiece.
The benefi ts are that you will protect both the
equipment and your own health. Your work area
will also be clean and safe.
- 27 -
05.09.2018 10:14:55 05.09.2018 10:14:55