Explanation Of Functions - Vivanco FMH 7190 Instrucciones De Uso

FMH 7190
Congratulations on purchasing your new Vivanco product. This wireless headphone
system operates using the latest transmission technology. Enjoy your favourite music or
films in top quality stereo sound without inconvenient cable connections. With the SRS
TruSurround XT® System you can also convert any normal stereo sound into breathtaking
virtual surround sound.
A Transmitter
1 Charging indicator light
2 Operation indicator light
3 SRS TruSurround XT®* indicator light
4 SRS TruSurround XT®* switch
5 Channel selection switch
6 Audio connecting cable
7 AC adaptor connector
8 AC adaptor
9 RCA adaptor
10 Jack adaptor 3.5 mm to 6.35 mm
B RF headphone
1 Charging contacts
2 Earshell with battery compartment
3 On/off switch (OFF/ON)
4 Volume control (VOL)
5 Operation indicator light
6 Channel selection button (TUNE)
7 Balance control left/right (L/R)
Important information
Please read these operating instructions carefully and keep them in a safe place.
Do not use the devices in water or rain.
The AC adaptors are designed for these devices only. Do not use the supplied AC
adaptors with other devices.
Avoid exposure to extreme heat or strong light.
Do not open the housings or the AC adaptors (danger of electric shock!).
Check whether the local mains voltage corresponds to the voltage indicated on the
AC adaptor.
Avoid touching the battery or charging contacts. Do not touch the contacts with
metal objects.
Do not cover the devices (e.g. with a towel, sheet, etc.)
Clean the devices using a moist cloth and never use aggressive cleaning agents.
Constant use at high volumes impairs your hearing and may cause permanent
damage.
Do not dispose of this product with the domestic waste; take it to your local
electronic waste recycling depot.
1
2
3
CHANNEL
Preparing your RF headphone
1. Place the transmitter near to your hi-fi system, your TV or another audio source.
2. Connect the AC adaptor to the connector on the transmitter, then plug it into a mains
socket.
8
GB
3. Connect the audio connecting cable to a headphone output, or to a line out or rec.
2
3
CHANNEL
out output. Set the volume of your audio source to 1/4 to 1/3 of the maximum
volume.
4. The operating indicator light on the transmitter lights up red when music is received.
5. Insert the supplied batteries as described in the chapter "Using batteries or
rechargeable batteries".
6. Switch on the RF headphone via the on/off switch.
R
7. Press the channel selection button on the RF headphone in order to automatically
locate the transmitter. If the transmitter has been located, the operating indicator
R
lights up green.
8. Your device is now ready for operation.

Explanation of functions

CHARGE
SRS TruSurround XT®*
ON
SRS TruSurround XT®* technology enables you to transform any normal mono or stereo
SRS
sound into outstanding surround sound.
SRS ON/OFF
To activate this function, make sure that a music signal is present. Press the SRS
TruSurround XT®* switch; the indicator lights up blue.
Auto-Tuning
If interference is received, select a different channel on the transmitter (channel select
switch). Then press the channel select button on the RF headphone and the new
transmitter is located automatically.
Balance
You can adjust the loudness ratio between the left and right channels. Turn the balance
1
control in the respective direction. The middle position produces a balanced sound image
between the left and right sides of the music signal.
L
Standby mode
The transmitter switches automatically to standby mode if it does not receive any signal
for 2 minutes or if the signal is too quiet. It switches automatically back to transmission
2
mode as soon as a signal is present again.
Using batteries or rechargeable batteries
Opening the battery compartment
3
1. To open the battery compartment, carefully pull off the ear cushion from the left side
earshell "L". The battery compartment is located behind this.
L
2. Insert the batteries or rechargeable batteries (micro, type AAA) into the battery
compartment, observing the correct polarity.
3. Place the ear cushion over the battery compartment again and press it carefully until
it latches.
GB
9