Operation - Ryobi P503 Manual Del Operador

Ocultar thumbs Ver también para P503:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WARNING:
Do not allow familiarity with products to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
 Cutting all types of wood products (lumber, plywood,
paneling, composition board, and hard wood)
This product will accept Ryobi One+ 18 V lithium-ion battery
packs and Ryobi One+ 18 V nickel-cadmium battery packs.
Both types of battery packs are shown on this page. Following
pages will show the lithium-ion 18 V battery pack.
For complete charging instructions, refer to the Operator's
Manual for the battery packs and chargers listed in the
General Safety Rules.
BATTERY PROTECTION FEATURES
Ryobi lithium-ion batteries are designed with features that
protect the lithium-ion cells and maximize battery life.
If the tool stops during use, release the trigger to reset and
resume operation. If the tool still does not work, the battery
needs to be recharged.
INSTALLING THE
BATTERY PACK
See Figure 4, page 15.
NOTE: The battery pack is shipped in a low charge condi-
tion. Therefore, it must be charged prior to use. Refer to
CHARGING BATTERY PACK for charging instructions.
 Place the battery pack in the saw. Align the raised rib
on the battery pack with the groove inside the saw, then
slide the battery pack into the saw.
 Make sure the latches on each side of your battery pack
snap into place and the battery pack is secured in the
saw before beginning operation.

OPERATION

CAUTION:
When placing battery pack in the tool, be sure raised
rib on battery pack aligns with the bottom of the tool
and latches into place properly. Improper installa-
tion of the battery pack can cause damage to internal
components.
REMOVING THE BATTERY PACK
See Figure 4, page 15.
 Locate the latches on the side of the battery pack and
depress them to release the battery pack from the saw.
 Remove battery pack from the saw.
WARNING:
Battery tools are always in operating condition. There-
fore, switch should always be locked when not in use or
carrying at your side.
KICKBACK
See Figures 5 - 8, pages 15 and 16.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
DANGER:
Release switch immediately if blade binds or saw stalls.
Kickback could cause you to lose control of the saw. Loss
of control can lead to serious injury.
To guard against kickback, avoid dangerous practices such
as the following.
 Setting blade depth incorrectly.
 Sawing into knots or nails in workpiece.
 Twisting the blade while making a cut.
 Making a cut with a dull, gummed up, or improperly set
blade.
 Supporting the workpiece incorrectly.
 Forcing a cut.
 Cutting warped or wet lumber.
 Operating the tool incorrectly or misusing the tool.
To lessen the chance of kickback, follow these safety prac-
tices.
 Keep the blade at the correct depth setting. The depth
setting should not exceed 1/4 in. below the material being
cut.
 Inspect the workpiece for knots or nails before cutting.
Never saw into a knot or nail.
 Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
9 - English

Publicidad

Tabla de contenido
loading

Tabla de contenido