Publicidad
Enlaces rápidos
Color
! Insert tubes into ColorQ with line and arrow facing forward.
! "
Sun
" = Shade meter from bright sunlight. Press/Hold button to turn off.
! "
Er7
" = Tube is misaligned, scratched, stained, or light chamber is stained.
See User Guide for more instructions.
! Brush and rinse all tubes promptly after use.
! Allow tubes to dry before returning to case.
! Replace reagent caps securely.
! If unit should auto-off during testing rinse and fill one tube to Blank and return
to testing.
! Use only LaMotte replacement reagents.
! bAt = Battery is low.
! Introduire le ColorQ droit.
s
! "
" = Maintenir l'appareil à l'ombre. Appuyer le bouton off pour l'eteindre.
! "
Er7
" =
Le tube est mal placé ou rayé, ou la caméra est tachée. Voir le Guide
de l'utilisateur pour toute autre instruction.
! Si l'appareil s'éteint automatiquement refaire un blanc et reprendre l'analyse.
! Essuyer et nettoyer tous les tubes correctement après l'usage.
! Permettre que les tubes se sechent bien avant de les réutiliser.
! Ferrer correctement les reactifs.
! Utilisez des réactifs LaMotte pour rechanger uniquement.
! bAt
=
Batterie basse.
! Insertar el tubo en el ColorQ recto.
! "
s
" = apartar el aparato de los rayos
del sol. Presionar/mantener el botón para
apagar.
! "
Er7
" =
El tubo está mal colocado o
rayado, o la cámara de lectura está
manchada. Para más instrucciones, consulte
la Guía del usuario.
! Si el aparato se auto-apaga durante el test,
llenar un tubo para el Blanco y volver al
análisis.
! Enjuagar y limpiar todos los tubos
adecuadamente después del uso.
! Permitir que los tubos se sequen antes de
volver a usarlos.
! Cerrar correctamente los reactivos.
! Utilice unicamente los reactivos LaMotte.
(tabletas grado instrumento).
! bAt = Batería baja.
TesTabs
Q
Pro-9
PO Box 329 • Chestertown • Maryland • 21620 • USA
800-344-3100 • 410-778-3100 • 410-778-6394
www.lamotte.com
®
TABLET VERSION
Order Code 2069
WARNING! This set contains chemicals
that may be harmful if misused. Read
cautions on individual containers carefully.
Not to be used by children except under
adult supervision.
3.18
62069
Publicidad
Manuales relacionados para LaMotte ColorQ TesTabs Pro-9
Resumen de contenidos para LaMotte ColorQ TesTabs Pro-9
- Página 1 ! Essuyer et nettoyer tous les tubes correctement après l'usage. ! Permettre que les tubes se sechent bien avant de les réutiliser. ! Ferrer correctement les reactifs. ! Utilisez des réactifs LaMotte pour rechanger uniquement. ! bAt Batterie basse. ! Insertar el tubo en el ColorQ recto.
- Página 2 Quitar el tubo. * Reagent is a potential health hazard. Read SDS at www.lamotte.com. * Los reactivos son peligrosos para la salud. Leer SDS en www.lamotte.com. * Les reactifs sont dangereux pour la santé. Reactivos son peligrosos. Lire SDS en www.lamotte.com.
- Página 3 ColorQ Range: 0-10 ppm chlorine, FREE CHLORINE/BROMINE 0-22 ppm bromine DPD 1 - Code 6903A-J Color 1. Add 1 DPD1 Tablet to same tube. 2. Cap. Shake for TEN seconds. Invert slowly 5 times. Insert tube into ColorQ. 3. Press button to read “FCL” Free Chlorine. NOTE: To read as Bromine, press button past “FCL”...
- Página 4 TOTAL CHLORINE ColorQ Range: 0-10 ppm chlorine, 0-22 ppm bromine DPD 3 - Code 6197A-J Color Color 1. Remove cap from reacted FCL (Free Chlorine) tube. 2. Add 1 DPD 3 Tablet. Shake for TEN seconds. Invert slowly 5 times. 3.
- Página 5 ColorQ Range: 6.5-8.5 pH - Code 3880A-J Color 1. Fill a clean tube to the 5mL line with water sample. 2. Add 1 Tablet. Crush with tablet crusher. 3. Cap. Invert 3 times to mix. Insert tube into ColorQ. 4. Press button to read “PH” pH. Remove tube. 1.
- Página 6 ALKALINITY ColorQ Range: 0-250 ppm ALK - Code 3882A-J Color 1. Press button to go to “ALY” Total Alkalinity. 2. Fill a clean tube to the 5mL line with water sample. 3. Add 1 Tablet. Crush with tablet crusher. 4. Cap. Invert 10 times to mix. Insert tube into ColorQ. 5.
- Página 7 CALCIUM HARDNESS ColorQ Range: 0-400 ppm * CaHard - Code 3883A-J Color 1. Press button to go to “CH” Calcium Hardness. 2. Fill a clean tube to the 5mL line with water sample. 3. Add 1 CaHard Tablet. Crush THOROUGHLY with tablet crusher. 4.
- Página 8 CYANURIC ACID (STABILIZER) ColorQ Range: 0-125 ppm *CYA - Code 6996A-J Color 1. Press button to go to “CYA” Cyanuric Acid. 2. Fill a clean tube to the 5mL line with water sample. 3. Add 1 tablet. Crush with tablet crusher. Cap. 4.
- Página 9 COPPER ColorQ Range: 0-4 ppm *Copper - Code 3808A-J Color 1. Press button to go to “COP” Copper. 2. Fill a clean tube to the 5mL line with water sample. 3. Add 1 COP BCA tablet. Crush with tablet crusher. Cap. 4.
- Página 10 IRON ColorQ Range: 0-3 ppm *Ir - Code 3725A-J Color 1. Press button to go to “Ir” Iron. 2. Fill a clean tube to the 5 mL line with water sample. 3. Add 1 IRON Tablet. Crush with tablet crusher. 4.
-
Página 11: La Solucion De Biguanuros (Phmb)
BIGUANIDE ColorQ Range: 0-70 ppm Biguanide (PHMB) Test Solution Code 3919-G Color 1. Press button to go to “bi g ” Biguanide. 2. Fill a clean tube to the 5 mL line with water sample. 3. Add 5 drops of BIGUANIDE (PHMB) TEST SOLUTION 4. - Página 12 BIGUANIDE SHOCK (PEROXIDE) ColorQ Range: 0-160 ppm b S h Biguanide Shock - Code 6930A-J Color 1. Press button to go to “b S h” Biguanide Shock. 2. Fill a clean tube to the 5 mL line with water sample. 3.