Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY
ASSEMBLING MOBILE BASE WHEELS
1. Turn the Base (Fig.1-
A) upside down and
mount the 2 non-
swiveling wheels (B)
to the base using one
M8x50mm Hex head
screw and one M8
flat washer for each
wheel.
2. Attach the leveling feet (C) to the base by
screwing the threaded portion of the foot into the
threaded holes in the base.
3. Attach the swiveling
foot pedal (Fig.2-D) to
the base using two M8 x
20mm Carriage bolts and
two M8 hex nuts.
4. Turn the base back over so that the wheels
are on the ground and adjust the leveling feet
until the unit does not rock or wobble.
MOUNTING JOINTER TO BASE
IMPORTANT: The machine is heavy, two peo-
ple are required to unpack and lift. Use a safety
strap to avoid tip over when lifting machine.
1. Remove the access panel on the rear of the
jointer by removing the six M6 Phillips head
screws that fasten the panel. Be sure the cut-
terhead pulley on the motor is in line with the
cutout in the top of the stand so the drive belt
can pass through.
2. Using a helper,
lift
the
jointer
onto
the
stand
Fig.3
(Fig.3).
3. The jointer attaches with three M10 x 25mm
socket head cap screws, three M10 lock wash-
ers and three M10 flat washers.
Two
are
accessible
through the panel in
the rear of the jointer.
The third is accessed
through
the
dust
chute (Fig. 4-B).
4. Tighten all three screws securely using the
supplied hex wrench.
Fig.1
C
A
B
Fig.2
D
Fig.4
B
E N G L I S H •
ASSEMBLING BELT AND ALIGNING PULLEYS
1. Place a straight edge along the face of
the motor pulley and the cutterhead pul-
ley. Make certain that they are aligned. If
an adjustment is necessary, you can reposi-
tion the motor pulley on the shaft of the
motor by loosening the set screw on the mo-
tor pulley and moving the motor pulley un-
til it is aligned with the cutterhead pulley.
2. Place
the V-belt
onto the cutterhead
pulley (Fig.5-A).
3. Position the V belt
over the motor pul-
ley (Fig.5-C). It may
be necessary to repo-
sition the motor in
order to get the belt
onto the motor pul-
ley. If this is the case,
loosen the 4 bolts (not
shown)
that
fasten
the motor to the dust chute and reposition the
motor until the belt can be fitted onto the mo-
tor pulley. Retighten bolts.
NOTE: If it is necessary to move the motor, be
sure to recheck pulley alignment after doing so.
4. Once the belt is positioned on both pulleys,
check the belt tension by squeezing the belt at
its midpoint. Proper tension is achieved when
there is approximately 1" deflection at the cen-
ter span of the belt using light finger pressure.
5. If an adjustment is necessary, raise or lower
the motor until proper tension is achieved.
WARNING: The outside edge of the pulley
must never be extended past the end of the
motor shaft in any circumstance.
ADJUSTING BELT TENSION
1. Correct belt tension is obtained when there
is approximately 1" deflection at the center
span of the belt using light finger pressure.
2. If an adjustment is required, the motor can
be raised or lowered to obtain the correct belt
tension.
3. Tighten motor mounting hardware after
tension is applied, making sure alignment of
the pulleys is not disturbed.
4. Replace the cutterhead pulley guard.
U se r's m a nua l
A
C
Fig.5
23
Publicidad
Tabla de contenido
