Milwaukee 2615-20 Manual Del Operador página 4

Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Installing Bits
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the
application.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. Remove the battery pack.
2. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
3. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
4. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
Using the Adjustable Clutch
This tool has an adjustable clutch for driving different
types of screws into different materials. When prop-
erly adjusted, the clutch will slip at a preset torque
to prevent driving the screw too deep and to prevent
damage to the screw or tool.
To adjust the clutch, turn the clutch adjusting dial so
that the desired setting lines up with the arrow on the
motor housing, as shown.
Driving
The torque specifications shown here are approxi-
mate settings obtained with a fully charged battery
pack.
Clutch
Setting
NOTE: Because the settings shown in the table are
only a guide, use a piece of scrap material to test
the different clutch settings before driving screws
into the workpiece.
When the maximum torque output for the clutch set-
ting is reached, the tool will stop and the red Torque
LED will flash. Release the switch to reset.
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
FORWARD
For Forward (clockwise) rotation, push the control
switch as shown. Check the direction of rotation
before use.
For Reverse (counterclockwise) rotation, push the
control switch as shown. Check direction of rota-
tion before use.
To Lock the trigger, push the control switch to the
center position. The trigger will not work while the
control switch is in the center locked position. Always
lock the trigger or remove the battery pack before
performing maintenance, changing accessories,
storing the tool and any time the tool is not in use.
Starting, Stopping and Controlling Speed
1. To start the tool, pull the paddle switch.
2. To stop the tool, release the paddle switch.
3. To vary the driving speed, increase or decrease
Drilling
age, always check the work area for hidden pipes
and wires before drilling or driving screws.
This tool provides a quick, convenient means of drill-
ing small holes and installing and removing screws.
Because of the many screw sizes, types, thread
engagements and materials available, it is difficult
to limit the application of this tool by screw size.
However, for applications in wood, a wood screw
with a full pilot hole is recommended.
4
1-4 Small screws in softwood.
5-7 Medium screws in softwood or small screws
in hardwood.
8-11
Large screws in softwoods. Medium screws
in hardwood or large screws in hardwood with
pilot hole.
Drill
Torque LED
Using Control Switch
LOCK - Push to CENTER
pressure on the paddle switch. The further the
paddle switch is pulled, the greater the speed.
APPLICATIONS
To reduce the risk of explosion,
WARNING
electric shock and property dam-
Applications
REVERSE