tau D749MA-R Guía Para La Instalación página 24

The radio control has very little range
a- Check that the ground and the aerial signal connections have not been inverted.
b- Do not make joints to increase the length of the aerial wire.
c- Do not install the aerial in a low position or behind walls or pillars.
d- Check the state of the radio control batteries.
The automation opens the wrong way
Invert the motor connections on the terminal block (terminals 28 and 29 for M1; terminals 23 and 24 for M2).
13. GUARANTEE: GENERAL CONDITIONS
TAU guarantees this product for a period of 24 months from the date of purchase (as proved by the
sales document, receipt or invoice).
This guarantee covers the repair or replacement at TAU's expense (ex-works TAU: packing and trans-
port at the customer's expense) of parts that TAU recognises as being faulty as regards workmanship
or materials.
For visits to the customer's facilities, also during the guarantee period, a "Call-out fee" will be charged
for travelling expenses and labour costs.
The guarantee does not cover the following cases:
• If the fault was caused by an installation that was not performed according to the instructions
provided by the company inside the product pack.
• If original TAU spare parts were not used to install the product.
• If the damage was caused by an Act of God, tampering, overvoltage, incorrect power supply,
improper repairs, incorrect installation, or other reasons that do not depend on TAU.
• If a specialised maintenance man does not carry out routine maintenance operations accord-
ing to the instructions provided by the company inside the product pack.
• Wear of components.
The repair or replacement of pieces under guarantee does not extend the guarantee period.
In case of industrial, professional or similar use, this warranty is valid for 12 months.
Manufacturer:
Address:
Declares under its sole responsibility, that the product: electronic control
unit
for use in a: Residential / Communities
Model: D749MA-R
Serial number: see silver label
Has been produced for incorporation on an access point (swing gate) of for assembly with other devices used to move such an ac-
cess point, to constitute a machine in accordance with the Machinery Directive 2006/42/EC.
Also declares that this product complies with the essential safety requirements of the following EEC directives:
- 2014/35/EU Low Voltage Directive
and, where required, with the Directive: - 2014/53/EU Radio equipment and telecommunications terminal equipment
Also declares that it is not permitted to start up the machine until the machine in which it is incorporated or of which it will be a
component has been identified with the relative declaration of conformity with the provisions of Directive 2006/42/EC.
The following standards and technical specifications are applied: EN 61000-6-2; EN 61000-6-3; EN 60335-1; ETSI EN 301 489-1 V1.9.2; ETSI EN
301 489-3 V1.6.1; EN 300 220-2 V2.4.1; EN 12453:2000; EN 12445:2000; EN 60335-2-103.
The manufacturer undertakes to provide, on sufficiently motivated request by national authorities, all information pertinent to the
quasi-machinery.
Sandrigo, 06/06/2017
Name and address of person authorised to draw up all pertinent technical documentation:
Loris Virgilio Danieli - via E. Fermi, 43 - 36066 Sandrigo (Vi) Italy
MANUFACTURER'S DECLARATION OF INCORPORATION
(in accordance with European Directive 2006/42/EC App. II.B)
TAU S.r.l.
Via E. Fermi, 43 - 36066 Sandrigo (Vi) - ITALY
Type:D749MA-R
Commercial name: Control panel for one-two 24V motors with encoder
designed for automatic movement of: Swing Gates
complete with: Radioreceiver and battery charger board
- 2014/30/EU Electromagnetic Compatibility Directive
Legal Representative
_________________________________________
Loris Virgilio Danieli
24