Blackstar Amplification ONE 200 Serie Manual De Instrucciones página 8

MIDI Channel Switching
The Series One offers the ability to control channel selection via MIDI Program
Change messages and interfacing with most MIDI controllers is a straight forward
process. The Series One can be placed in a MIDI chain allowing you to
simultaneously select a channel on the amplifier and change the patch on a MIDI
effects processor connected to the effects loop. There are 128 available Program
Changes, giving you the possibility to access a vast number of tonal combinations.
To set-up MIDI channel switching, simply connect the MIDI controller's MIDI Out
socket to the MIDI In socket on the rear of the amplifier. The controller should be set
to transmit Program Change messages (this is usually the case). From new, a Series
One amplifier is set to OMNI mode and responds to Program Change messages on
all MIDI channels. Changing 'patches' on the controller will change the selected
channel on the amp. The default settings for each Program Change number are
shown in the table below:
Program Channel
Change
1 CLEAN 33 CLEAN
2 CRUNCH 34 CRUNCH
3 OVERDRIVE 1 35 OVERDRIVE 1
4 OVERDRIVE 2 36 OVERDRIVE 2
5 CLEAN 37 CLEAN
6 CRUNCH 38 CRUNCH
7 OVERDRIVE 1 39 OVERDRIVE 1
8 OVERDRIVE 2 40 OVERDRIVE 2
9 CLEAN 41 CLEAN
10 CRUNCH 42 CRUNCH
11 OVERDRIVE 1 43 OVERDRIVE 1
12 OVERDRIVE 2 44 OVERDRIVE 2
13 CLEAN 45 CLEAN
14 CRUNCH 46 CRUNCH
15 OVERDRIVE 1 47 OVERDRIVE 1
16 OVERDRIVE 2 48 OVERDRIVE 2
17 CLEAN 49 CLEAN
18 CRUNCH 50 CRUNCH
19 OVERDRIVE 1 51 OVERDRIVE 1
20 OVERDRIVE 2 52 OVERDRIVE 2
21 CLEAN 53 CLEAN
22 CRUNCH 54 CRUNCH
23 OVERDRIVE 1 55 OVERDRIVE 1
24 OVERDRIVE 2 56 OVERDRIVE 2
25 CLEAN 57 CLEAN
26 CRUNCH 58 CRUNCH
27 OVERDRIVE 1 59 OVERDRIVE 1
28 OVERDRIVE 2 60 OVERDRIVE 2
29 CLEAN 61 CLEAN
30 CRUNCH 62 CRUNCH
31 OVERDRIVE 1 63 OVERDRIVE 1
32 OVERDRIVE 2 64 OVERDRIVE 2
14
65 CLEAN 97 CLEAN
66 CRUNCH 98 CRUNCH
67 OVERDRIVE 1 99 OVERDRIVE 1
68 OVERDRIVE 2 100 OVERDRIVE 2
69 CLEAN 101 CLEAN
70 CRUNCH 102 CRUNCH
71 OVERDRIVE 1 103 OVERDRIVE 1
72 OVERDRIVE 2 104 OVERDRIVE 2
73 CLEAN 105 CLEAN
74 CRUNCH 106 CRUNCH
75 OVERDRIVE 1 107 OVERDRIVE 1
76 OVERDRIVE 2 108 OVERDRIVE 2
77 CLEAN 109 CLEAN
78 CRUNCH 110 CRUNCH
79 OVERDRIVE 1 111 OVERDRIVE 1
80 OVERDRIVE 2 112 OVERDRIVE 2
81 CLEAN 113 CLEAN
82 CRUNCH 114 CRUNCH
83 OVERDRIVE 1 115 OVERDRIVE 1
84 OVERDRIVE 2 116 OVERDRIVE 2
85 CLEAN 117 CLEAN
86 CRUNCH 118 CRUNCH
87 OVERDRIVE 1 119 OVERDRIVE 1
88 OVERDRIVE 2 120 OVERDRIVE 2
89 CLEAN 121 CLEAN
90 CRUNCH 122 CRUNCH
91 OVERDRIVE 1 123 OVERDRIVE 1
92 OVERDRIVE 2 124 OVERDRIVE 2
93 CLEAN 125 CLEAN
94 CRUNCH 126 CRUNCH
95 OVERDRIVE 1 127 OVERDRIVE 1
96 OVERDRIVE 2 128 OVERDRIVE 2
Program Change Assignment
To change the default assignments and set the amp up to respond to a different set
of Program Changes:
1. The amp must be powered on with either the Standby switch set to on, a jack
in the Input socket, or both.
2. Send the appropriate Program Change message to the amp.
3. Press and hold in the appropriate front panel Channel Select switch for
2 seconds.
The corresponding channel will be selected and its LED will flash three times in quick
succession to indicate it has been assigned to the last received Program Change.
The amplifier will now remember the selection. Repeat the operation until all your
Program Changes have the desired amp channel assigned to them.
MIDI Receive Channel Selection
As mentioned previously, the default mode is set to OMNI and the amplifier will
respond to MIDI Program Changes on all MIDI channels. You may wish to set the
amplifier to respond to Program Changes on just a single MIDI channel. The Series
One can be set to respond in this way for any of the first seven MIDI channels as
follows:
1. The unit must be in standby (Power (34) on and Standby (33) off), and no lead
connected to the Input jack.
2. Simultaneously press and hold the Clean (3) and OD1 (17) Select switches.
3. After 2 seconds the LED for OD2 (20) will begin to flash continuously (2 flashes
per second) to indicate that the unit is in MIDI Receive Channel Program Mode.
4. Release the Clean (3) and OD1 (17) Select switches and select the required MIDI
channel by using the Channel Select switches as shown in the table below:
Clean Crunch OD1 MIDI CHANNEL
OFF OFF OFF OMNI
ON OFF OFF 1
OFF ON OFF 2
ON ON OFF 3
OFF OFF ON 4
ON OFF ON 5
OFF ON ON 6
ON ON ON 7
The corresponding Channel Select LEDs will illuminate to show the selection and
each press of the Channel Select switches will toggle the state of its associated
LED.
5. To store the desired selection press the OD2 (21) Select switch. The OD2 (20)
Select LED will flash quickly four times when the operation is complete. The unit
will then revert to normal operation, and will respond only to Program Changes
on the newly selected MIDI Channel.
15