Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
17. Cutting elements continue to rotate after the
motor is switched off.
18. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
19. Take a rest to prevent loss of control caused
by fatigue. We recommend to take a 10 to
20-minute rest every hour.
20. Hold the power tool by insulated gripping
surfaces only, because the cutting tool may
contact hidden wiring. Cutting tool contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
21. Do not use the tool on steep slopes.
22. The shoulder harness must be used during
operation, if supplied with the tool.
23. Do not start the tool when the cutting tool is
tangled with cut grass.
24. Before starting the tool, be sure that the cut-
ting tool is not touching the ground and other
obstacles such as a tree.
25. Always keep your hands, face, and clothes
away from the cutting tool when it is rotating.
Failure to do so may cause personal injury.
26. Only use the cutting tool that are marked with
a speed equal or higher than the speed marked
on the tool.
27. Do not touch the gear case during and immedi-
ately after the operation. The gear case becomes
hot during operation and can cause burn injury.
28. Do not use the tool when there is a risk of
lightning.
29. When you use the tool on muddy ground, wet slope,
or slippery place, pay attention to your footing.
30. Avoid working in poor environment where
increased user fatigue is expected.
31. Do not use the tool in bad weather where visi-
bility is limited. Failure to do so may cause fall or
incorrect operation due to low visibility.
32. Do not submerge the tool into a puddle.
33. Do not leave the tool unattended outdoors in
the rain.
34. When wet leaves or dirt adhere to the suc-
tion mouth (ventilation window) due to rain,
remove them.
35. Do not use the tool in the snow.
Maintenance instructions
1.
The condition of the nylon cutting head, pro-
tective devices must be checked before com-
mencing work.
2.
Turn off the motor and disconnect the portable
power pack from the tool before carrying out
maintenance, replacing the cutting tool and
cleaning the tool.
3.
Check for loose fasteners and damaged parts
such as cracks in the nylon cutting head.
4.
Follow instructions for lubricating and chang-
ing accessories if applicable.
5.
When not in use store the equipment in an
indoor dry location that is locked up or out of
children's reach.
6.
Use only the manufacturer's recommended
replacement parts and accessories.
7.
Inspect and maintain the tool regularly, espe-
cially before/after use. Have the tool repaired
only by our authorized service center.
8.
Keep handles dry, clean and free from oil and
grease. Keep all cooling air inlets clear of
debris.
9.
Always keep the tool in good working condi-
tion. Poor maintenance can result in inferior per-
formance and shorten the life of the tool.
10. Do not wash the tool with high pressure water.
11.
When washing the tool, do not let water enter
the electrical mechanism such as motor and
terminals.
12. When storing the tool, avoid direct sunlight
and rain, and store it in a place where it does
not get hot or humid.
13. Perform inspection or maintenance in a place
where rain can be avoided.
14. After using the tool, remove the adhered dirt
and dry the tool completely before storing.
Depending on the season or the area, there is a
risk of malfunction due to freezing.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
WARNING:
Use of this product can create
dust containing chemicals which may cause
respiratory or other illnesses. Some examples of
these chemicals are compounds found in pesti-
cides, insecticides, fertilizers and herbicides.
Your risk from these exposures varies, depend-
ing on how often you do this type of work. To
reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to filter out microscopic
particles.
Symbols
The followings show the symbols used for tool.
volts
direct current
no load speed
revolutions or reciprocation per minute
5 ENGLISH
Publicidad
Tabla de contenido
