Crown CT15262 Manual Original página 24

Symbol
Power tool designation
Mitre saw is designed for cutting timber blanks and
is best for clean angular cuts� Using special saw
blades enables you to cut plastic and aluminum
blanks� The power tool is designed for right-handed
users only�
Power tool components
1 Movable part of retaining bar
2 Clamp (assembly) *
3 Guard cover
4 Carrying handle
5 Handle
6 Spindle lock
7 Blocking lever
8 Sliding guard cover
9 Circular saw blade *
10 Retaining bar
11 Base plate
12 Turntable
13 Insert
14 Turntable swivel angle scale
15 Fixing lever
16 Turntable lock
17 Indicator
18 On / off switch
19 Extension bracket *
20 Butterfly screw of movable part of retaining bar *
21 Butterfly screw for fixing the clamp *
22 End stop *
23 Fixing bolt of retaining bar
24 Ventilation slots
25 Body angle lock (for carrying)
26 Clamping handle
27 Dust removing coupler
28 Dust bag *
29 Wrench *
30 Butterfly screw of the end stop *
31 Extension bracket fixing screw
32 Plate
33 Fixing screw of plate
34 Saw blade fixing bolt
35 External flange
36 Internal flange
37 Spindle
38 Body vertical position adjustment bolt lock-nut
39 Body vertical position adjustment bolt
40 Body tilt angle adjustment bolt lock-nut
41 Body tilt angle adjustment bolt
42 Body tilt angle scale
43 Body tilt angle indicator
44 Screw of body tilt angle indicator
Meaning
During operation, remove
the accumulated dust�
Do not dispose of the power
tool in a domestic waste
container�
45 Fixing screw of movable part of retaining bar *
46 Allen key *
47 Screw
* Optional extra
Not all of the accessories illustrated or described
are included as standard delivery.
Installation and regulation of power tool
elements
Before carrying out any works on the power tool it
must be disconnected from the mains.
Do not draw up the fastening ele-
ments too tight to avoid damaging the
thread.
Carriage position (see fig. 1)
The power tool can be moved only when positioned for
carriage (the body pulled down and fixed). Carry power
tool holding base plate 11 with both hands�
Before starting any work, position the power tool for
operation, follow these actions:
• slightly press handle 4;
• move lock 25 as shown onto fig. 1;
• lift the body up smoothly;
• to position the power tool for carriage, do the
indicated operations in a reverse order�
Dust bag mounting / dismounting (see fig. 2)
Before operation put dust bag 28 on dust removing
coupler 27 (see fig. 2). Dump and clean dust bag 28
in due time�
Extension bracket and end stop mounting /
dismounting (see fig. 3-4)
If you are planning to cut long blanks, you should
mount extension brackets 19, adjust them properly
(depending on the blank length) and fix them using
screws 31 (see fig. 3).
Use end stop 22 when cutting workpieces of equal
length�
Adjust extension brackets 19 and end stop 22
depending on the length of the blank (see fig. 4).
Clamp mounting / dismounting (see fig. 5)
In order to fix the blanks properly, mount clamp 2 and
fix it using butterfly screw 21 (see fig. 5.1). Adjust
clamp 2 depending on the length and thickness of the
blank (see fig. 5.1).
Replacement of the saw blade (see fig. 6-7)
After prolonged operation, the saw blade
can become very hot, remove it using
gloves. This will also reduce the risk of
injury by the cutting edge.
• Lift the body to the uppermost position�
• Shift moving sliding guard cover 8 to the extreme
upper position (see fig. 6.1).
English
24