Crown CT15262 Manual Original página 25

• Slacken fixing screw 33 (see fig. 6.1) and move the
plate 32 to the direction shown in fig. 6.2.
• Press spindle lock 6 and manually turn saw blade 9
in order to immobilize it� While pressing spindle lock 6,
turn off bolt 34 with wrench 29 (see fig. 7). Caution:
bolt 34 is left-hand threaded.
• Remove the following details from spindle 37:
external flange 35, circular saw blade 9 and internal
flange 36 (see fig. 7).
• Using soft brush, clean all details and install on
spindle 37: internal flange 36, circular saw blade 9,
external flange 35 (see fig. 7).
• While pressing spindle lock 6, tighten bolt 34 with
wrench 29� Release spindle lock 6�
• Perform actions shown in fig. 6 in reverse order:
move plate 32 to its original position, tighten fixing
screw 33, shift sliding guard cover 8 down�
• Ensure that saw blade 9 does not touch any power
tool elements and can rotate freely�
Vertical alignment of the body and adjustment of
the 45° tilt (see fig. 8-10)
• Position the body for carriage�
• Loosen clamping handle 26 and set the body tilt
angle (90° or 45°)� Tighten clamping handle 26�
• Place the sides of an alignment setsquare 90° or 45°
(depending on the angle to align) to the surface of saw
blade 9 and turntable 12� If the setsquare sides join the
surfaces of saw blade 9 and turntable 12 tightly, then
alignment is not needed, otherwise you have to do it�
Use bolt 39 and lock-nut 38 for vertical
alignment of the body (see fig. 8).
Use bolt 41 and lock-nut 40 for adjustment
of the body tilt angle 45° (see fig. 9).
• Loosen clamping handle 26�
• Loosen the lock-nut�
• Turning the adjustment bolt in or out, make the
sides of the 90° or 45° setsquare (depending on the
angle to adjust) join the surfaces of saw blade 9 and
turntable 12 tightly�
• Tighten the lock-nut�
• Loosen screw 44 and place indicator 43 to the 0° (on
scale 42) or 45° position (depending on the angle to
adjust), then tighten screw 44 (see fig. 10).
Retaining bar alignment (see fig. 11-12)
• Set the 0° horizontal cutting angle (the procedure is
described below)�
• Position the body for carriage�
• Place the sides of an alignment setsquare 90° to
the surface of saw blade 9 and retaining bar 10� If the
setsquare sides join the surfaces of saw blade 9 and
retaining bar 10 tightly, then alignment is not needed,
otherwise you have to do it�
• Slacken butterfly screw 20 and turn off screw 45 with
screwdriver (see fig. 11.1).
• Remove movable parts 1 of retaining bar 10 to
access the fixing bolts 23 (see fig. 11.2).
• Slacken fixing bolts 23 with the help of Allen key 46
(not included in delivery set) and move retaining bar 10;
ensure that the sides of alignment setsquare 90° fit
tightly to the surface of circular saw blade 9 and to the
surface of retaining bar 10 (see fig. 12).
• Tighten fixing bolts 23 with the help of Allen key 46
(not included in delivery set)�
• Install movable parts 1 of retaining bar 10 to its
original position and screw in screw 45 with screwdriver�
Initial operation of the power tools
Always use the correct supply voltage: the power
supply voltage must match the information quoted on
the power tool identification plate.
Switching the power tool on / off
Switching on:
Press blocking lever 7 with thumb of the right hand
(see fig. 13) - this will enable you to pull the power tool
body down� Press on / off switch 18�
Switching off:
Release on / off switch 18�
Dust suction during the power tool op-
eration
Dust suction allows reducing dust concen-
tration in the air and prevents its accumula-
tion at the workplace�
While operating the power tool, always use
dust bag 28 or a vacuum cleaner suitable for collecting
process-generated dust� A special adapter is used to
join the vacuum cleaner to coupler 27�
Recommendations on the power tool op-
eration
Alignment of the horizontal cutting angle (see
fig. 14-15)
• Loosen lock 16 and press fixing lever 15 (see fig. 14.1).
• While pressing fixing lever 15, set the cutting angle
by turning table 12 by lock 16� Indicator 17 shows the
set cutting angle on scale 14 (see fig. 15).
• Release fixing lever 15 and tighten lock 16�
You can preset
(45°, 31�6°, 22�5°, 15°, 0° etc�)�
• Loosen lock 16 and press fixing lever 15�
• While pressing fixing lever 15, set the cutting angle
by turning table 12 by lock 16� As soon as indicator 17
shows one of the frequent angles (45°, 22�5°, 0°, etc�)
on scale 14 - release fixing lever 15, and the chosen
angle will be properly fixed, you do not have to tighten
lock 16 in this case�
Alignment of the vertical cutting angle (see
fig. 16, 10)
• Loosen clamping handle 26 (see fig. 16.1).
• Set the cutting angle by tilting the power tool body
(see fig. 16.2). Indicator 43 shows the set cutting
angle on scale 42 (see fig. 10).
• Tighten clamping handle 26 (see fig. 16.3).
Cutting (see fig. 17)
• Place the power tool on the worktable and prefer-
ably fix it with bolts or cramps.
English
25
the most frequent angles