Makita HP0300 Manual De Instrucciones página 6

Ocultar thumbs Ver también para HP0300:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 33
Speed change
► Fig.3: 1. Speed change lever
CAUTION:
Always set the speed change lever
fully to the correct position. If you operate the
tool with the speed change lever positioned halfway
between the "1" side and "2" side, the tool may be
damaged.
CAUTION:
Do not use the speed change lever
while the tool is running. The tool may be damaged.
Position of
Speed
speed
change lever
1
Low
2
High
To change the speed, switch off the tool first. Select
the "2" side for high speed or "1" for low speed but high
torque. Be sure that the speed change lever is set to the
correct position before operation.
If the tool speed is coming down extremely during the
operation with "2", slide the lever to the "1" and restart
the operation.
Adjusting the fastening torque
► Fig.5: 1. Action mode changing ring 2. Adjusting
ring 3. Graduation 4.
The fastening torque can be adjusted in 20 levels by turning the adjusting ring. Align the
on the tool body. Then, align the graduations with the arrow on the tool body. You can get the minimum fastening
torque at 1 and maximum torque at 20.
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application. The following shows the rough guide of the relationship between
the screw size and graduation.
Graduation
Machine screw
Wood
Soft wood
screw
(e.g. pine)
Hard wood
(e.g. lauan)
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Torque
Applicable
operation
High
Heavy load-
ing operation
Low
Light loading
operation
marking 5. Arrow
1
2
3
4
5
6
M4
Selecting the action mode
CAUTION:
your desired mode mark. If you operate the tool
with the ring positioned halfway between the
mode marks, the tool may be damaged.
CAUTION:
from "
" to other modes, it may be a little dif-
ficulty to slide the action mode changing ring. In
this case, switch on and run the tool for a second
at the "
" position, then stop the tool and slide
the ring to your desired position.
► Fig.4: 1. Action mode changing ring 2. Adjusting
ring 3. Graduation 4. Arrow
This tool has three action modes.
Drilling mode (rotation only)
Hammer drilling mode (rotation with
hammering)
Screwdriving mode (rotation with clutch)
Select one mode suitable for your work. Turn the
action mode changing ring and align the mark that you
selected with the arrow on the tool body.
7
8
9
10
11
M5
ɸ3.5 x 22
ɸ4.1 x 38
ɸ3.5 x 22
Installing or removing driver bit/
drill bit
CAUTION:
make sure that it is firmly secured. If it comes out, do
not use it.
► Fig.6: 1. Tighten 2. Sleeve 3. Ring
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the driver bit/drill bit in the
chuck as far as it will go. Hold the ring firmly and turn
the sleeve clockwise to tighten the chuck.
To remove the driver bit/drill bit, hold the ring and turn
the sleeve counterclockwise.
6 ENGLISH
Always set the ring correctly to
When you change the position
marking with the arrow
12
13
14
15
16
17
M6
ɸ4.1 x 38
After inserting the driver bit/drill bit,
18
19
20

Publicidad

Tabla de contenido
loading

Tabla de contenido