Bosch AdvancedAquatak 150 Manual Del Usuario página 18

18 | English
Press the safety lock (back button on the gun handle) to re-
lease the trigger. Fully press the trigger until there is a con-
stant flow of water to clear the air from the machine and wa-
ter supply hose. Release trigger. Press the safety lock (front
button on the gun handle).
Turn button on main switch. Point the power gun down-
wards. Press the trigger safety lock to release the trigger.
Fully press the trigger.
Autostop Function
The machine is designed to switch off the motor when the
trigger is released on the gun.
Working Advice
General
Never use a roto nozzle or pencil jet to clean motor
u
vehicles.
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the
ma-chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure
hose. Do not expose the high pressure hose to sharp edges
or corners.
Warning! The Patio Cleaner is only suitable for use on level
surfaces! Do not attempt to use them on steps. Never at-
tempt to touch the rotating nozzle while operating the ma-
chine!
Working advice for cleaning with detergents
Only use cleaning agents suitable specifically for high
u
pressure washers.
We recommend that you use detergent sparingly for the sake
of the environment. Observe the recommended dilution on
the detergent label.
The high-pressure foam nozzle supplied with this product in-
cludes a regulator to control detergent use. Adjust as re-
quired.
Recommended cleaning method
Step 1: Attach the fixed fan nozzle and remove the heavy
dirt.
Troubleshooting
Problem Possible Cause
Motor refuses to start Plug not connected
Mains socket faulty
Fuse faulty / blown
Extension cable damaged
Motor protector has activated
F 016 L81 291 | (13.07.2018)
Step 2: Attach the foam bottle and spray on the detergent
sparingly.
Step 3: Rinse off the loosened dirt and detergent with the
fan nozzle.
Note: When cleaning a vertical surface spray off dirt/deter-
gent from the bottom and work in an upwards direction.
Rinse from the top and work downwards.
Use with alternative water sources
This high-pressure washer will self prime and can draw water
from water tanks and natural water sources. It is IMPORT-
ANT that the water is clean and the BOSCH inlet filter is clear
and fitted to the machine.
Open tanks/containers and natural water
sources
Use the Self Priming accessory kit comprising:
– Inlet strainer with non return valve
– 3 m reinforced supply hose
– Universal coupling to the pressure washer
This enables the pressure washer to draw water up to 0.5 m
above the water level in the source in approximately 15
seconds.
Submerge the 3 m hose in water to displace the air. Connect
the 3 m supply hose to the pressure washer ensuring that
the inlet strainer remains submerged in the water source.
Run the pressure washer with the lance disconnected until a
steady flow of water appears from the high pressure hose.
Stop if this has not been achieved within 25 seconds and
check all the connections. Switch off and connect the lance
and nozzle to operate.
It is important to ensure that all hose and coupling connec-
tions are of good quality, air tight and that all washers are in
good condition and correctly seated in place. Failure to do
so may affect the self priming performance.
Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a
suitable tap outlet, first connect the supply hose (not
provided) to the tank outlet, open the tap to allow the water
to displace all the air in the hose and then connect to the
pressure washer.
Corrective Action
Connect plug
Use another socket
Replace fuse
Try without extension cable
Allow to cool for 15 minutes
Bosch Power Tools