GYS SMARTMIG 142 Manual De Instrucciones página 12

PROCESS OF REELS AND TORCHES ASSEMBLY (FIG-V)
Remove the Nozzle (fig V-E) from the torch by turning clockwise and then remove the contact tip, leaving the support
and the spring on the torch (fig V-D).
• Open the door of the machine
FIG V-A : Position the reel on to the support.
• In case of 100mm (3P, 142, 152, 162) wire reel use, do not install the adapter (1).
• Adjust the reel break (2) to avoid reel movement tangling the wire when welding stops. Be careful not to tighten
too much - the reel must rotate without straining the motor.
• Tighten the plastic screw (3).
FIG V-B : Installing the drive roller.
• Choose the correct diameter reel for the type of wire. The visible diameter indicated on the roller when fitted in
place is the diameter currently in use (ie. 0.8mm is visible for use with 0.8mm wire).
FIG V-C : To select the adjustment of the drive rollers, proceed as follows :
• Loosen the drive roller knob as far as possible.
• Insert the wire until it exits the other side by about 2cm, tighten the knob again slightly.
• Start the motor by pressing the trigger of the torch.
• Tighten the knob (fig V-C) whilst pressing the trigger until the wire starts to move.
Nb : When welding with Aluminium, use the minimum possible pressure to avoid crushing the wire
• Pull the wire out of the end of the torch by approximately 5cm, then attach the contact tip suitable for the wire used
and then the nozzle (fig V-E).
The SMARTMIG 142, 152, 162, 3P machines can accommodate coils of 100 or 200mm diameter.
The SMARTMIG 182 machines can accommodate coils of 200 or 300mm diameter. To place a 200mm wire reel, first
install the adapter (ref. 042889) on the support.
The SMARTMIG 3P can also weld with rutile electrodes of 2.0/ 2.5/ 3.2 mm diameter.
Below are the different combinations possible :
Smartmig 142/152
steel/ 0,6/0,8
stainless
steel
Alu*
No Gas
Electrodes
* We recommend a teflon sheath (ref. 041578) and special Aluminium contact tip (Ø 0.8 ref. 041059 - Ø 1.0 ref.
041066)
To help you select the diameter of wire suitable for the job you want to perform, refer to the table on page 4 (FIG IV).
GAS COUPLING
- Connect a pressure regulator to the gas bottle. Connect the welding machine using the pipes supplied, and place
the two clamps to avoid leakages.
- Set the gas flow by adjusting the dial located on the pressure regulator.
NB : to help facilitate the adjustment of the gas flow, operate the drive rollers by pressing the trigger of the torch
(ensure that the drive roller is completely loose so the wire is not fed through).
This procedure does not apply to "Gasless" welding mode.
CONTROL PANEL (FIG. VI)
Smartmig 142/152/162/182/183
1- Voltage selection button A / B
2- Voltage selection button min/max.
3- Wire speed regulator.
4- « SMART » settings table MIG/MAG
5- Thermal Protection light.
6- positions switch
12
162
-
0,9
- -
SMARTMIG
3P 182
0,6/0,8/1,0
0,8/1,0
0,9/1,2
2/2,5/3,2 -
1- Mode select button MIG/MMA.
2- Power adjustment knob MMA or MIG.
3- Wire speed regulator.
4- Voltage selection button A / B
5- « SMART » settings table MIG/MAG & MMA.
6- Thermal Protection light.
183 gaz
Argon +
CO2
Pure Argon
-
- -
Smartmig 3P
EN