Setting Bass Sound Control; Setting Bass Compressor; Setting Bass Focus; Speaker Setup - Alpine IVA-W205 Manual De Operación

9
Touch [RETURN] to return to the previous screen.
• When the speaker is set to the "OFF" mode, the parametric
equalizer for that speaker cannot be set. Refer to "Setting the
Speakers" (page 43).
• It is not possible to adjust the frequencies of adjacent bands within 7
steps.
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker's playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the 40 Hz
or 20 Hz band has no effect. Additionally, you may overload and
damage the speakers.
• When the parametric EQ is adjusted, the adjustment for graphic EQ
becomes ineffective.

Setting Bass Sound Control

1
Check that Defeat mode is off (page 25).
2
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
3
Touch [AUDIO].
The AUDIO SETUP screen appears.
4
Touch [ ] of A.PROC.
The A.PROCESSOR list is displayed.
5
Touch [ ] of BASS SOUND CONT.
The BASS SOUND CONT. screen appears.

Setting Bass Compressor

You can adjust the sound of low frequencies as desired.
6
Touch [ ] or [ ] of BASS COMP. to select the
desired mode.
Bass sound is emphasized more as the mode is
sequentially switched as MODE 1
vivid low frequencies.
Select OFF when the setting is not necessary.
Touch [RETURN] to return to the previous screen.

Setting Bass Focus

Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With an
initial delay of 0.1 ms for each of the 0 to 200 steps, audible time
correction can be achieved.
6
Set the delay number in the front and rear, and on
the right and left of the desired speaker by touching
the respective [ ] or [ ] button.
• Any setting in Bass Focus is applied in time correction, too (page 44).
• Touch [RETURN] to return to the previous screen.
46
-EN

Speaker Setup

The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-forwarding
1
2
3
4
5
6
*
*
• The subwoofer can be set only to ON/OFF.
• If the center speaker is turned "OFF", the center channel's audio
2 3, offering you
• If you set the speaker response to "OFF", also set the speaker setting
• Perform the setup for all the speakers ("Front", "Center" ,"Rear"
• When center is set to "OFF", the setting is ineffective even if center
• Through changing the settings on each speaker, a change in the
• When using the PRO LOGIC II, if the rear speaker is set to
or switching the audio channel of this unit while making this
adjustment. The setting is canceled if Decode mode is switched.
Check that Defeat mode is off.
Touch [SETUP] on the main source screen.
The SETUP selection screen appears.
Touch [AUDIO].
The AUDIO SETUP screen will appear.
Touch [ ] of A.PROC.
The A.PROCESSOR list screen appears.
Touch [ ] of SPEAKER SETUP.
The adjusting screen of SPEAKER SETUP appears.
Select the speaker characteristic by touching [ ],
[ ] of the desired speaker setting.
1
*
OFF : When no speaker is connected.
SMALL: When a speaker that cannot play low frequencies
(80 Hz or less) is connected.
2
*
LARGE : When a speaker that can play low frequencies
(80 Hz or less) is connected.
1
It is not possible to set the front speakers to "OFF".
2
If the front speakers are set to "SMALL", the rear and center
speakers cannot be set to "LARGE".
signals are added to the audio signals output from the front speakers.
to "OFF" (page 43).
and "Subwoofer"). If not, the sound may not be balanced.
is set with this function.
output of the other speakers may occur due to the setting
requirements.
"LARGE", then there will be no output from the subwoofer.