Functional Description - Makita DDF484 Manual De Instrucciones

FUNCTIONAL
DESCRIPTION
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Al w ays s w itch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery cartridge
firmly when installing or removing battery cartridge.
Failure to hold the tool and the battery cartridge firmly may
cause them to slip off your hands and result in damage to
the tool and battery cartridge and a personal injury.
Fig.1: 1. R e d i n d i c a t o r 2. Button 3. B a t t e r y c a r t r i d g e
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery
capacity
Only for battery cartridges with "B" at the end of the
model number
Fig.2: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for few seconds.
Indicator lamps
Lighted Off
Remaining
capacity
Blinking
7 5 % t o 100%
5 0% t o 7 5 %
25 % t o 5 0%
0% t o 25 %
C h a r g e t h e
battery.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the tool/battery is operated in a manner that causes
it to draw an abnormally high current, the tool automat-
ically stops without any indication. In this situation, turn
the tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.
Overheat protection
When the tool/battery is overheated, the tool stops
automatically. In this situation, let the tool/battery cool
before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
NOTE: Overheat protection (for battery) will work only
with batteries with star marking.
Fig.3: 1. S t a r m a r k i n g
Sw itch action
Fig.4: 1. S w i t c h t r i g g e r
CAUTION:
Before installing the battery car-
tridge into the tool, al w ays check to see that the
s w itch trigger actuates properly and returns to
the " OFF " position w hen released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
t r i g g e r . R e l e a s e t h e s w i t c h t r i g g e r t o s t o p .
NOTE: The tool automatically stops if you keep pull-
ing the switch trigger for about
Lighting up the front lamp
Fig.5: 1. L a m p
CAUTION:
Do not look in the light or see the
source of light directly.
6 ENGLISH
Off Blinking
malfunctioned.
minutes.
Remaining
capacity
The battery
m a y h a v e