Makita DDF484 Manual De Instrucciones página 7

Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out approximately 10 seconds after
r e l e a s i n g t h e s w i t c h t r i g g e r .
NOTE: When the tool is overheated, the tool stops auto-
matically and the lamp starts flashing. In this case, release
the switch trigger. The lamp turns off in one minute.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Reversing sw itch action
Fig.6: 1. R e v e r s i n g s w i t c h l e v e r
CAUTION:
Al w ays check the direction of
rotation before operation.
CAUTION:
Use the reversing s w itch only after
the tool comes to a complete stop. C h a n g i n g t h e
direction of rotation before the tool stops may dam-
a g e t h e t o o l .
CAUTION:
W hen not operating the tool,
al w ays set the reversing s w itch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
t e r c l o c k w i s e r o t a t i o n .
Adjusting the fastening torque
Fig.8: 1. Adjusting ring 2. Graduation 3. Arrow
The fastening torque can be adjusted in
on the tool body. You can get the minimum fastening torque at 1 and maximum torque at
The clutch will slip at various torque levels when set at the number 1 to 1. The clutch does not work at
t h e m a r k i n g .
Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which
torque level is required for a particular application.
The following shows the rough guide of the relationship between the screw size and graduation.
Graduation
M a c h i n e s c r e w
Soft wood
W o o d
s c r e w ( e .g . p i n e )
H a r d w o o d
(e.g. lauan)
ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing or removing driver bit/
drill bit
Fig.9: 1. S l e e v e 2. C l o s e 3. O p e n
levels by turning the adjusting ring. Align the graduations with the arrow
1 2 3 4 5 6
M 4
–
–
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Speed change
Fig.7: 1. S p e e d c h a n g e l e v e r
CAUTION:
fully to the correct position. If you operate the
tool with the speed change lever positioned halfway
between the 1 side and
d a m a g e d .
CAUTION:
w hile the tool is running. The tool may be damaged.
Displayed
Number
1
2
To change the speed, switch off the tool first. Push
the speed change lever to display
or 1 for low speed but high torque. Be sure that the
speed change lever is set to the correct position before
o p e r a t i o n .
If the tool speed is coming down extremely during the
operation with display
a n d r e s t a r t t h e o p e r a t i o n .
7 8 9 10 11 12
M 5
ɸ3 .5 x 22 ɸ4 .1x 3 8
ɸ3 .5 x 22
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
Installing hook
Fig.10: 1. G r o o v e 2. H o o k 3. S c r e w
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
7 ENGLISH
Al w ays set the speed change lever
side, the tool may be
Do not use the speed change lever
Speed Torque
L o w H i g h
H i g h L o w
for high speed
, push the lever to display 1
m a r k i n g .
13 14 15 16 17 18
M 6
–
ɸ4 .1x 3 8
Applicable
operation
H e a v y l o a d -
i n g o p e r a t i o n
L i g h t l o a d i n g
o p e r a t i o n
19 20 21
–