Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
8) SWR ADJUSTMENT
This function allows to adjust the SWR (Standing Wave Ratio) by beep tones.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
phone to
select
the SWR function.
2.
Press the rotary PUSH knob (6). The radio automatically goes to
without pressing PTT switch (17) . The SWR measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to 1. 0 . The space
between two beeps became longer when SWR value moves away from1. 0 .
Display shows the SWR value. For example 2. 5 .
5.
Press PTT switch (17) to
exit
MENU mode.
*Volume of the beep tone is adjustable with VOLUME knob (1). Please check
that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 6.
9) MIC TYPE
The PRESIDENT WALKER II FCC can be used with an electret microphone as
well as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram
page 56). Turning on the unit, the type of the microphone is briefly dis-
played.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the MIC TP function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the type on the microphone EL (electret) or DY (dynamic).
4.
New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to
adjust
another function or b) Press the PTT switch (17) to
validate
exit
MENU.
and
disappears.
5.
If no key is pressed, the unit
exits
the display.
Default type of microphone is EL (electret).
10) PA SETTING
This function allows to
select
the operating mode of Public Address.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the PA SET function.
2.
Press PUSH knob (6) to
validate.
enter
MENU.
is displayed.
TX
disappears in the display.
enter
MENU.
is displayed.
The current parameter blinks on LCD.
MENU after 10 seconds,
disappears in
enter
MENU.
is displayed.
The current value blinks on LCD.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the operating mode of the PA : I n, OF or PA.
4.
New press PUSH knob (6) to validate. The parameter stops blinking. a) Go
back to point 1 to
adjust
validate
exit
MENU.
and
5.
If no key is pressed, the unit
mode
the display.
I n: the
modulation of the microphone
speaker connected to jack PA.SP. (D). The
the internal loudspeaker [or external optional loudspeaker connected to
jack EXT.SP (C)]. "PA" blinks alternately with the modulation mode (AM).
OF: The reception is no more functional. Only the
phone
is transmitted to the Public Address loudspeaker connected to jack
PA
PA.SP. (D). PA and
PA: the
modulation of the microphone
ted to the Public Address loudspeaker connected to jack PA.SP. (D).
MODE: "PA" blinks alternately with the modulation mode (AM).
The MIC GAIN knob (4) to
Default PA setting is: I n.
See § PA (Public Address) page 9.
11) RESET
Restores all factory settings.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the RESET function.
2.
Press PUSH knob (6) to
3.
New press PUSH knob (6) to reset. The unit
4.
If no key is pressed, the unit
press on PUSH knob(6) key.
D) FUNCTION WITH PTT SWITCH
TALKBACK LEVEL
This function allows to adjust the volume level of the TALKBACK.
1.
Activate the TALKBACK function (see § TALKBACK page 8).
2.
Press and hold the PTT switch (17) then turn the rotary PUSH knob (6) to
increase
(clockwise) /
the TALKBACK.
3.
Release the PTT switch (17).
12
another function or b) Press the PTT switch (17) to
disappears.
exits
MENU after 10 seconds,
is transmitted to the external loud-
received signal
modulation of the micro-
volume level are displayed.
and the
received signal
adjust
the audio level of the mode PA.
enter
MENU.
is displayed.
validate.
AL blinks on LCD.
exits
MENU.
exits
MENU after 10 seconds or by a new long
decrease
(counterclockwise) the volume level of
disappears in
is transmitted to
are transmit-
PA
disappears.
Publicidad
Tabla de contenido
