EINHELL GC-BC 25/1 I AS Manual De Instrucciones Original página 20

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Safety devices
When working with the equipment, the appropri-
ate plastic guard hood for cutting blade mode or
cutting line mode must be fi tted to prevent objects
being thrown out by the equipment. The integra-
ted blade in the cutting line guard hood automati-
cally cuts the line to the optimum length.
Explanation of the warning signs on the
equipment (Fig. 14):
1. Warning!
2. Read the directions for use before operating
the equipment.
3. Wear protective headgear, goggles and ear
muff s.
4. Wear sturdy, non-slip footwear.
5. Wear safety gloves.
6. Protect the equipment from rain and damp.
7. Be careful of objects being thrown out!
8. Always switch off the equipment and pull out
the spark boot plug before carrying out any
maintenance work.
9. All bystanders must be kept at least 15 m
from the machine.
10. The equipment continues to rotate!
11. Caution: Hot equipment parts. Keep your dis-
tance.
Anl_GC_BC_25_1_I_AS_SPK9.indb 20 Anl_GC_BC_25_1_I_AS_SPK9.indb 20
GB
12. Add a little grease (gear grease) after every
20 hours in operation!
13. Beware of recoil!
14. Do not use any saw blades.
2. Layout and items supplied
2.1 Layout (Fig. 1-13)
1. Guide pin adapter
2. Guide pin
3. Operating handle
4. Starter cable
5. Choke lever
6. Gas tank
7. Fuel pump (primer)
8. Air fi lter housing cover
9. ON-OFF switch
10. Screwdriver
11. Throttle lever
12. Locking knob for throttle lever
13. Spool with nylon line
14. Nylon line protective hood
15. Cutting blade safety cover
16. 4 ea. screws M5 (25 mm)
17. Carrying strap
18. Cutting blade
19. Operating handle retainer
20. 4 ea. screws M5 (20 mm)
21. 4 ea. nuts M5
22. Driving plate
23. Pressure plate
24. Pressure plate cover
25. Nut M10 (left-hand thread)
26. Combined oil/petrol cylinder
27. Spark plug wrench
28. Open-ended spanner 8/10mm
29. Allen wrench 4 mm
30. Allen wrench 5 mm
31. 2 ea. Tie wraps
32. Knurled screw M6
33. Nut M6
34. Washer Ø 6mm
35. Air fi lter
36. Spark plug boot
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
- 20 -
14.05.2019 13:46:19 14.05.2019 13:46:19