The Water Dispenser - KitchenAid W10537977A Guía De Uso Y Cuidado

4. When 1 cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the
word "Confirm" to confirm the calibration.
A
A. 1 cup of water
5. When Measured Fill calibration has been confirmed the icons
will disappear and the display will return to the home screen.

The Water Dispenser

IMPORTANT:
Dispense at least 1 qt (1 L) of water every week to maintain a
fresh supply.
If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
With the water filter removed, dispense 1 cup (237 mL) of
water. If 1 cup (237 mL) of water is dispensed in
8 seconds or less, the water pressure to the refrigerator
meets the minimum requirement.
If it takes longer than 8 seconds to dispense 1 cup
(237 mL) of water, the water pressure to the refrigerator is
lower than recommended. See "Water Supply
Requirements" and "Troubleshooting" for suggestions.
To Dispense Water - Standard:
1. Press a sturdy glass against the dispenser paddle.
2. Remove the glass to stop dispensing
To Dispense Water - Measured Fill:
Measured Fill allows you to dispense a specified amount of water
with the touch of a few buttons.
NOTE: The amount of water you select will be dispensed. Make
sure the container is empty and that it can hold the entire volume.
If ice is in the container, you may need to adjust your selection.
1. Press MEASURED FILL to turn the feature on. When the
feature is on, the Measured Fill screen appears on the display.
REFRIGERATOR USE
Press ICE MODE, under Back, to manually turn off the
Measured Fill feature and return to the home screen.
NOTE: The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned off,
any changes you have made will be lost and all defaults will
be restored.
2. You can dispense water by the ounce, cup, or liter. The
default unit is ounces. To switch to cups or liters, press the
LIGHT button under Units.
Default, minimum, and maximum volumes are listed in the
following chart:
Units Default
Ounces 8
Cups 1
Liters 0.25
3. Press the LOCK (+) and OPTIONS (-) buttons to adjust the
volume as desired. The LOCK button increases the volume,
and the OPTIONS button lowers the volume.
NOTES:
When increasing or decreasing the dispense volumes, if
an adjustment button (-/+) is held for approximately
10 seconds or longer the control may stop responding.
Release the button for approximately 2 seconds and then
continue making the adjustment.
Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]
per cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
4. To dispense water, press a sturdy glass against the water
dispenser lever OR place the glass below the water dispenser
and press the MEASURED FILL button.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
5. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser lever OR
press the MEASURED FILL button a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show how
much water remains to be dispensed. The display will turn off
after 1 minute of inactivity.
6. To select a new volume or start dispensing the same volume
again, you must first finish dispensing the selected volume, or
turn off the Measured Fill feature (either by waiting 1 minute so
it will automatically turn off or by pressing ICE MODE to
manually turn it off) and then turn it back on.
Minimum Maximum
1 128
¹/₄
16
0.05 4.00
23