Black and Decker KG2023 Manual De Instrucciones página 6

ENGLISH
Fitting and removing grinding or cutting discs (fig. C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data). The maximum thickness for grinding discs
is 6 mm, for cutting discs 3.5 mm.
Fitting
Fit the guard as described above.
x
Place the inner flange (11) onto the spindle (6) as shown
x
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (6) as shown (fig. D).
x
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
x
Place the outer flange (14) onto the spindle. When fitting
x
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. E). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. E).
Keep the spindle lock (4) depressed and tighten the outer
x
flange using the two-pin spanner (15) (fig. F).
Removing
Keep the spindle lock (4) depressed and loosen the outer
x
flange (14) using the two-pin spanner (15) (fig. F).
Remove the outer flange (14) and the disc (12).
x
Use
Warning! Let the tool work at its own pace.
x
Do not overload.
Carefully guide the cable in order to avoid accidentally
x
cutting it.
Be prepared for a stream of sparks when the grinding or
x
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
x
provides optimum protection from the grinding or cutting
disc.
Switching on and off
To switch the tool on, press the lock-off button (2) and
x
subsequently press the on/off switch (1).
To switch the tool off, release the on/off switch (1).
x
Warning! Do not switch the tool off while under load.
Hints for optimum use
Firmly hold the tool with one hand around the side handle
x
and the other hand around the main handle.
When grinding, always maintain an angle of approx. 15°
x
between the disc and the workpiece surface.
6
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots in your tool using a
x
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
x
Do not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
x
Connect the brown lead to the live terminal in the new plug.
x
Connect the blue lead to the neutral terminal.
x
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Protecting the environment
Black & Decker provides a facility for recycling
Black & Decker products once they have reached the
end of their working life. This service is provided
free of charge. To take advantage of this service
please return your product to any authorised repair
agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com.
Technical data
Voltage
Power input
No-load speed
Disc diameter
Disc bore
Spindle size
Weight
EC declaration of conformity
Black & Decker declares that these products conform to:
98/37/EC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55014
L (sound pressure): 86.6 dB(A), L
pA
102.7 dB(A), hand/arm weighted vibration 2.9 m/s
KG2023
KG2000 KG2001
V 230 230
AC
W 2,000 2,000
-1
min 6,500 8,400
mm 230 180
mm 22 22
M14 M14
kg 7 7
(acoustic power)
WA
2