Publicidad
QU I C K I N S TA L L G U I D E
SYS TE M G RO UNDING (E ART HING)
General grounding
GROUND ALL SYSTEMS ACCORDING TO THESE INSTRUCTIONS BEFORE YOU CONNECT POWER LEADS.
FOLLOW INSTRUCTIONS EXPLICITLY TO ENSURE THE SAFETY OF PERSONNEL.
Cabinets always require redundant and independent equipment grounding conductors between the cabinet and the wiring system ground: an insulated
grounding conductor and a supplementary (protective) ground.
Grounding conductor
The grounding conductor is provided as part of the three-wire, 15-Amp, AC-power cord set included with the equipment. If the power cord must be
replaced, use a power cord of the same gauge that has the same insulation, number of conductors, and usage ratings.
Protective Grounding conductor
earth ground before you make any other connections to the equipment. The protective grounding conductor must be:
• An Insulated wire, #5 (13mm2) to #14 (2mm2) AWG, with green and yellow stripes
• Connected to the grounding stud on the back of the cabinet.
TE C H NI CA L S U PPORT
The NVT Phybridge Technical Support Group is available to assist you with product installation, configuration, monitoring and troubleshooting procedures.
Should you experience trouble with this equipment or for repair or warranty information, please contact NVT Phybridge Inc. at
+1 905.901.3633 or support@nvtphybridge.com.
TE C H NI CA L S PEC IF ICATIONS
Model
Part Number
Dimensions
Weight
Mounting
Processor
Memory
Interface: Ethernet Uplink
(Trunk IP)
Interface: Downlink
(PoE and IP to adapter)
Management
Power Supply
Power Output
Power Consumption
Power Injection (PoE)
PowerWISE® Power Sharing
Operating Temperature
Humidity
Specifications subject to change without notice.
888.901.3633 | +44 (0) 208 977 6614 | www.nvtphybridge.com
CLEER24
NV-CLR-024
19 inches x 1U Without rack ears:
(HxWxD) 1.75" x 17.13" x 9.92" (4.45cm x 43.5cm x 25.2cm)
7.94lb (3.6kg)
Standalone or rack or shelf-mountable 2 brackets included for installation
Broadcom BCM56018 switch processor, 266MHz
32MB FLASH, 64MB DDR SDRAM
Maximum 2 uplinks, each 1Gb/s (full duplex), either:
• 2 mini-GBIC ports: 1000 Base-TX/SX/LX/EX/ZX/LHX (determined by SFP, transceiver module installed), Ethernet IEEE 802.3z,
• 2 RJ45 ports: 10/100/1000 Base-T autosensing, independent speed selection, Ethernet IEEE 802.3, CAT5e copper cable
24 x BNC Jacks
Speed: 100Mb/s (full duplex)
PoE Power: 30 Watts Maximum (See Appendix)
Maximum Distance: (100 Mbit/s):
• 1500' (457M) over RG59 Coax Cable
• 2000' (610M) over RG6 Coax Cable
• 3000' (915M) over RG11 Coax Cable
24 x Status LEDs:
1 LAN port (MGMT): RJ45, 10/100 Base-T autosensing, IEEE 802.3 1 UART console port:
RJ45 (Rj45 to DB9 cable included)
Hot-Swappable Power Supply Unit Autosensing 100-240VAC, 50/60 Hz
500W at 100VAC,
1000W max at 240VAC
16.5W
DC voltage: 48VDC to 56VDC
Endpoint devices must be compliant with IEEE 802.3af/at
2 male connectors (rear), DC IN and DC OUT: 48VDC to 56VDC
14°F to 122°F (-10°C to +50°C)
10% to 95% (non-condensing) at 35° C
Maximum Distance: (10 Mbit/s):
• 4500' (1220M) over RG59 Coax Cable
• 6000' (1830M) over RG6 Coax Cable
• 6000' (1830M) over RG11 Coax Cable
Copyright 2020 NVT Phybridge | 413-0001-G | Page 6
Publicidad
